|Dec 24, 2005, 06:05 PM|
Joined May 2005
9 motors 30g with stats, where is the best ?
I'm looking for a 30g outrunner
I find this :
HiModel A2406-32T KV1150 TP Series Outrunner Brushless Motor
KV 1150 33g 15$
APC10*47SF 4300RPM 7.2V 6.8A 310g
2207 DIY Brushless Motor
KV ?? 32.5g 19$
8x6SF 2S 5A 4900RPM
KV 1100 33g 35$
2 cell 8x4 7100 RPM 3.7A
2 cel 8x6 6100 RPM 5.4A
2 cell = 7.4V ??
MP Jet Outrunner Brushless Motors AC 22/7-45D
KV ?? 26g 37$
A20-34S - 27mm Outrunner BL motor (1500kv)
KV 1500 28g 37$
EP7035 7.72v 4.70A 268g
MicroDAN 2505 3D Series
KV 1030 34g 55$
APC9*4.7SF 6.8V 5.3A 313g !!
HYPERION Z-2205 46
GWS9x4.7SF 6.8V 6.7A 5295RPM
KV 1380 24.5g 66$
APC7x4SF 7.2V 212g 4.7A
GWS8x4HD 6.8v 240g 4.75A
Moteurs Donuts-Models 2C/24/280
KV 1380 24.5g 74$
9x4.7 2S 330g
so, where is the best (quality/price)
|Dec 25, 2005, 09:59 AM|
Edmonds Wa. (Seattle)
Joined Nov 2003
Ya I am still around!
23g 12a $49.99
|Dec 25, 2005, 06:49 PM|
If weight is important, the Axi is the lightest motor in your list. It is also a proven performer in Shockie style planes.
My non-Lexan Little Screamer with a mount weighs exactly the same as an AXI.
The AXI is a lot quieter than the aptly named Screamer.
|Dec 26, 2005, 07:24 AM|
Joined May 2005
there are 22mm and 25mm
there are 9 and 12 tooth stator
the best (for indoor flying, slow with big thrust) is 12 tooth and 25mm ?
I 'm not sure if Hyperrion is a 12 tooth ?
|Dec 26, 2005, 08:55 AM|
AFAIK, the Hyperion is a 12 slot LRK motor like the AXI.
Slow with big thrust is not always the best.
With a big prop it is almost impossible to stop the plane from torque rolling in a hover. With a smaller prop and the right plane you can do an anti-torque roll.
My first Shocky had a 2208 (39 gram) motor swinging a 10x4.7 on 2S. Lots of thrust, but a hover was always a torque roll.
When they became available the 2204, although down a bit in thrust, was a much better motor choice. Switching to 3S gets back all the thrust.
Also larger props are heavier. This is important when you are trying to shave a few grams here and there.
If you want to see how a small prop high rpm setup can work check out the Knuffel videos here .
The Knuffel is intended for a sub-20 gram motor swinging a 7" prop.
What plane are you going to use this motor in?
|Dec 26, 2005, 09:55 AM|
What plane are you going to use this motor in? Quote: Pat M.
Agreed! Trying to decide which motor is best without knowing its intended use is like asking which apple makes a better pie, It all depends on the tree!
But, there's allways a selection of prop weights across a given size range
|Dec 26, 2005, 06:00 PM|
12 vs 9 slot is something a lot of people stuggle over on which to use. I personally chose to build 9 slot motors to save weight, but the microdans are very nice and can swing very large props with ease.
Indoors you are right you want less pitch speed, but then again you also want to keep your indoor planes light...
I am sure I just confused you even more, but really there is no cut and dry answer.
|Jan 07, 2006, 06:55 AM|
Joined May 2005
I buy the Volare 2815
here my test with Emeter
Moteur Volare 2815 (7A/60s max):
HELICE V A RPM Grams
GWS SF 9x4.7 6.6 4.4 4700 240
GWS SF 9x4.7 7.35 5 5040 280
GWS SF 9x4.7 7.26 5.2 5100 290 (timming 30°)
GWS SF 8x4.3 7.47 3.6 5890 235
GWS SF 8x4.3 6.53 2.9 5290 190
GWS SF 8x4.3 7.4 3.8 6000 240 (timming 30°)
GWS SF 8x6 6.67 3.8 4980 200
GWS SF 8x6 7.4 4.5 5360 235
GWS SF 7x6 6.58 3.1 5330 150
GWS SF 7x6 7.45 3.6 5880 190
GWS SF 7x6 9.91 5.4 7310 300
grams was calc with :
It is good ? no ?
|Jan 07, 2006, 10:57 AM|
This is rather outdated but might be of some use.
MicroDAN 2505/10 and the newer Littlescreamers are not in here, nor are the latest CustomCDR Billet motors.
Edit: Here is a link to MicroDAN 2505/10 performance and that of other small motors with 8x4 and 9x5 GWS HD props.
Here's a link to Custom CDR Single data:
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Where is best price for electronic soldering iron & supplies?||CheeseWing||Electric Plane Talk||9||May 29, 2010 04:36 PM|
|Where is the best place to buy Hacker motors||JPA2002||Power Systems||3||Mar 09, 2004 07:40 AM|
|Where is the best price on the GWS Tigermoth?||Scomis||Parkflyers||9||Nov 23, 2001 01:45 PM|
|Where is the best E-buy for FMA Razor 400?||rlt55||Foamies (Kits)||0||Aug 02, 2001 06:30 PM|
|For 9.6V 1600ma NIMH battary what is the best charge rate and charge time?(more)||clchen||Parkflyers||1||May 06, 2001 05:23 AM|