Jan 02, 2012, 02:33 PM Gig 'Em! United States, TX, College Station Joined Nov 2010 655 Posts The wire length he lists for 1280 (18.49"/469.8mm) and the quarter wavelength (2.31"/60mm) do not work out. He says the 60mm should be an eighth of the wire length. I'll try 235mm for each leaf (I was using 240, which the CL dimension) this time and see how that ends up. Last edited by TexasAggie; Jan 02, 2012 at 02:40 PM.
Jan 02, 2012, 02:43 PM
I think it'll work this time!!
399 feet above Roanoke, VA
Joined Jan 2007
3,461 Posts
Quote:
 Originally Posted by TexasAggie The wire length he lists for 1280 (18.49"/469.8mm) and the quarter wavelength (2.31"/60mm) do not work out. He says the 60mm should be an eighth of the wire length. I'll try 235mm for each leaf (I was using 240, which the CL dimension) this time and see how that ends up.
Sounds good! I hope your trash can has less wire in it than mine!!
 Jan 02, 2012, 02:46 PM Gig 'Em! United States, TX, College Station Joined Nov 2010 655 Posts Well I bought a 2lb spool of welding wire, so it has the potential to be stuffed...
 Jan 02, 2012, 02:56 PM Gig 'Em! United States, TX, College Station Joined Nov 2010 655 Posts Here's where the discrepancy exists: his quarter-wave metric calculations are screwy. 75168/1280 = 58.7 NOT 60. The lengths in his photos also don't agree with his computations.
Jan 02, 2012, 03:05 PM
I think it'll work this time!!
399 feet above Roanoke, VA
Joined Jan 2007
3,461 Posts
Quote:
 Originally Posted by TexasAggie Here's where the discrepancy exists: his quarter-wave metric calculations are screwy. 75168/1280 = 58.7 NOT 60. The lengths in his photos also don't agree with his computations.
Don't forget to add a little for the hooks and the tail on the ground side.
 Jan 02, 2012, 03:07 PM Gig 'Em! United States, TX, College Station Joined Nov 2010 655 Posts I'm leaving the hooks off of this one, and the tails don't matter since they're attached when the center conductor is shielded.
Jan 02, 2012, 06:29 PM
Registered FPVer :)
Switzerland, LU, Buchrain
Joined Aug 2006
2,893 Posts
Quote:
 Originally Posted by TexasAggie My first SPW attempt turned out pretty nicely. I'll put up pictures in a little while. One question: In the below video, the angles that are supposed to be about 17 degrees turned out to be about 40 degrees in mine. Is this okay or should I redo it?
40 degrees is a lot. Try it out. If they perform good enough for what you are after - who cares! If not, you found one point to improfe.

It seems like the relation of the arc length compared to the two legs is not ok then. Usually the arc should be about half the wafelength, the legs about a quarter. Note though that the correction factor to apply differs between the SPW and the CL antenna.

HTH

Markus
 Jan 03, 2012, 08:39 AM Engineer for Christ Amherst, VA Joined Jun 2006 10,940 Posts TexasAggie - You might find the little hooks help a lot. They won't harm anything at 1.3GHz. I make them as long as the feedpoint gap so the overall lobe lenght is consistent. The lobes should be .5% longer than 1 full wavelength depending on the wire thickness you use. Wire thickness will change resonant wavelength, so the little details will change. Generally the thicker the wire, the higher the resistance (I know this sounds backwards but we're talking RF, not DC). My calculations were done with .035" wire. if you use thinner wire (say .030 or .025) you will need the lobes to be slightly longer than my calculations. -Alex
Jan 03, 2012, 09:19 AM
Gig 'Em!
United States, TX, College Station
Joined Nov 2010
655 Posts
I've got .030 welding wire. So do I need to add the length of the hook to the lobe length, or get the lobes correct and then just bend the last few mm into the hook? Also, how important is that 105 angle? Without another dimension, I find that it can be physically anywhere in a fairly large range. Seems 115 gives a nice-looking lobe. That dashed line on the left is tangent to the arc at the corner.

Edit: I'm going to be doing the trick in your YouTube video with the legs, so I'll make 4 independent lobes.

# Images

Last edited by TexasAggie; Jan 03, 2012 at 09:44 AM.
Jan 03, 2012, 09:28 AM
Gig 'Em!
United States, TX, College Station
Joined Nov 2010
655 Posts
Since you're here, Alex, can you take a quick look at my FPV test flight from yesterday and give any troubleshooting tips you can think of? 1280 MHz. Tx is a generic 400 mW from RMRC. Rx is Lawmate unmodified. Both antennas were cloverleafs. The transmitter antenna was slightly better-made than the receiver antenna. I highly doubt the problem is due to the Tx turning off in flight, since I replaced all my wiring.