|Aug 26, 2012, 08:57 PM|
E-Oculus from the Mfg
I have been asked to convert the RES Oculus to a E-fuse. So here it is! I will be showing the step by step of how I will be putting mine together. This will be a E-fuse added to a already built wing and tail set from my RES Oculus. Hope to have it ready for the Visalia Fall Fest ALES contest on Oct 5th.
|Aug 26, 2012, 08:58 PM|
I pulled the fuse out of the mold and trimmed it. It came in at 10.05 oz painted.
Today I picked up the rest on my parts to put in my E-Oculus fuse.
This is a list of what I have now!
Battery 3 - 1300 2S 65C Thunder Power http://thunderpowerrc.com/html/G6Pro...sBatteries.htm
Motor Hacker A30 10XL, 700W 900KV http://www.aero-model.com/Hacker-Bru...-A30-10XL.aspx
Speed control X-70SB Pro http://www.aero-model.com/Hacker-Bru...B-Pro-ESC.aspx
Spinner 45mm OD with a 5mm shaft http://www.hobbyking.com/hobbyking/s...idProduct=5566
Prop 15 X 8 http://www.espritmodel.com/aeronaut-...denthaler.aspx
RX battery 1000 2C Thunder Power
Servos Elevator 5085MG, Rudder HS 85BB http://www.hitecrcd.com/products/dig...hs-5085mg.html
|Aug 26, 2012, 08:59 PM|
Well I have all the parts bench tested. Motor going the right way "with out the props off"! Already to install the gear. Will be working on it all day tomorrow. Hope to have it in the air Sunday. Will post pics when done.
|Aug 26, 2012, 09:03 PM|
I worked all day Saturday and some Sunday morning to get the E-Oculus ready for the test flight today. Had to redesign almost everything inside. I mounted a HS-85BB servo in the tail upside down head forward. The arm sticks out just a little that I put a clear fairing over it. The link is short and clean setup. Used some E-6000 glue to hold the wires in place in the tail boom. Under the I put a peace of 1/8" ply for a servo & RX mount. The elevator servo is a HS-5085MG. Had to lay it on it's side to place the push rod in line on the side of the fuse. Didn't want to add a binding spot in the push rod. The RX is a AR9300. I need to drill some holes to run the antenna out of the fuse. I found a 45mm spinner to use on this fuse so that I can mount the Hacker motor inside. Cutting the fuse back to fit the spinner was a job all of it's own. The ply motor mount is sanded round to make the fuse fit the shape of the spinner. It is so tight that I had to glue the wires to the top of the fuse. After getting everything glued in and were I wanted it the time came to balance it. Set up the CG stand this morning and thinking that the battery would be how I was going to move the CG around. It was not even close to where I thought would be. It was placed just behind the motor next to the speed control. OK it fits there.
After all that made it to the flying field with everything test two or three times. Looked at the radio program of a friends setup and had to make some changes to the elevator comp for launch. With it already to go it just looked to fast to fly. That red fuse makes it look like a rocket. Everyone was waiting for me to test fly it. I wanted to do all the set up test just like on a new model. Rang check, program settings check, motor check, surface check, glide test check. Ready for launch! Now everyone wanted to know what I was waiting now?
Time to MAN UP! It's that time to launch! First flight got a toss and powered up. This thing went for the Moon. With the elevator comp set up not just right I was able to fly it up to the 200 meters with NO problems. The CG and trim was off a little but no big deal!
The second flight was so different changed some trims and setups. This flight was timed and got a cool launch photo. This plane flies just the same as the RES plane just with a little more weight on board.
Now that I have all of my info with this new project I will making the changes on the print and adding some new instructions for the E-Oculus kit. The E-fuse kit is available now.
New ALES plane E-Oculus
Thanks to all of my friends that pushed me to do this project!
Having a blast doing it!
|Sep 13, 2012, 12:28 PM|
United States, AZ, Surprise
Joined Jul 2002
I noticed you are using a 1000 2cell for Rx power. Have you considered
a Castle Creations 10A BEC? Lighter and plenty of power for two servos
and spoilers. Just a thought.
|Sep 17, 2012, 08:53 AM|
Congratulations! That's a great modification.
I like your bellcrank. What thickness G10 did you use?
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Build Log||Oculus RES Build||onethermal||Thermal||1202||Oct 29, 2014 08:01 PM|
|Discussion||Good kit mfgs, dying breed? (non-ARF) UPDATE: active mfgs. listed!||Wacky1||The Builders Workshop||26||Apr 27, 2012 03:42 PM|
|Rant||A mistake buying from CENTURY JET MFG!!||Kmot||Fuel Warbirds||23||Oct 11, 2007 05:03 PM|
|Question||Search plan : Tri-Star from SIG mfg||Zappi||Electric Plane Talk||7||Apr 10, 2005 02:01 PM|
|TP2100 pack ruptured from MFG||Darren Hintze||Batteries and Chargers||2||Mar 29, 2004 11:58 AM|