|Wingspan:||1200 mm (47.2 in)|
|Wing Area:||21.31dm2 (330 in2)|
|Weight:||278-290 gm (9.8-10.2 oz)|
|Wing Loading:||13-13.6 gm/dm2 (4.3-4.5 oz/ft2)|
|Battery:||4.8v 300mAH NiMH|
The first time I saw someone fly a DLG (discus launch glider) plane I was stunned. I immediately started doing my research on DLGs and the issue I had was the price - expensive! I did finally get a DLG and to date I have owned 3. I think there is no purer form of flight in the RC world. You control your ailerons, elevator and rudder. You have to rely on your plane and your brains to find thermals to keep the plane in the air.
What I really wanted was something small enough to throw in the car and inexpensive enough to not worry about. The trick to that equation is finding an airframe that is up to the task. When I saw Dream-Flight was releasing my dream plane I was quick to contact them. The plane arrived quickly and my questions were answered just as fast.
|Dream-Flight Libelle DLG Review - RCGroups.com (10 min 20 sec)|
The medium sized box shown with a dragon fly wing as the art. Libelle is German for dragonfly.
Most of the hard work is done for you.
The manual covers the complete build process. I was left with no questions about the exact steps needed to build the Libelle. I would also like to note that the manual is as much a soaring and trimming guide as it is an assembly guide.
All hardware needed is included. I'm pretty picky about hardware and everything that shipped with the Libelle worked for me. Be careful not to lose the small clevis screws!
The wing comes in two halves. Carbon fiber is preinstalled in the wing halves.
The stabilizer simply screws in place on the factory installed stab mount.
The rudder has a channel molded into it that allows you to CA it on. You can also use epoxy. I went with CA and it has held up fine to flying. I also used some tape like the instructions suggested.
This plane is made for the Hitec HS-35HD. Be sure to power these servos up and find center before installing them on the plane. This is done to prevent damage to servo. Dream-Flight also offers servo extensions that you can buy separately from their online store.
The only limitation for the receiver is that is has to fit in the small fuselage. I found the Minima6E was perfect for this since the servos connected on the side and not the top.
I ran the antenna wires down the side of the fuse.
Dream-Flight sells a battery that is made to fit in the nose of the fuse. It is a 4.8v 300mAH NiMH battery. Everything I have these days is lithium polymer so I wasn't sure how I was going to charge it. I used my charging cable from my Hitec Aurora to charge this battery.
I was able to fly the Libelle on a calm day and a very windy day. The concern anyone would have with a low cost DLG bird is how does it fly? I thought it flew great. Even though it only weighs around 10 ounces it still managed to penetrate the air. The flip side to that is that at 10 ounces you could really milk the air that you had. It also really communicates to you while flying, If there is a thermal you will see it.
I set all the control surfaces to neutral and the only trimming I had to do was on the elevator. After we pulled a little weight from the nose that worked itself out too. It is a great flying machine.
The next question is how tough is it? It's made out of foam so that was a concern. The rudder was my biggest concern since it is going to be in contact with the ground every time you land. I'm happy to report it held up fine. At one point I did a full speed nose plant. The only thing that happened was the servos in the fuse needed some CA added to lock them back into place. I was impressed. I think the light weight of the plane is what keeps it from sustaining any major damage.
While we didn't find any thermals on our initial flights we managed to keep the plane in the air a good while and have a fun. We even did some slope flying off a very small embankment next to our field.
There is a lot to like about this plane. The price is what should grab you first. If you ever wanted to try your hand at flying a discus launch glider this is the plane for you. I think it's smaller size and light weight make it a great grab-and-go plane for the field or the beach.
Jason Cole spent the day flying the Libelle with me and he said, "From my POV it's a great entry level DLG. It won't match performance of a competition one, but its good enough to be fun."
I will post updates this spring and summer after I have more thermal hunting time with the Libelle.
The build is simple and fast and you don't need anything fancy to build the plane. I built the whole thing sitting at my office table. The plane is obviously designed by real DLG pilots. The construction is light and strong.
I had a blast flying the Libelle and I'm excited to have it in my arsenal of planes. I see some early summer lunch breaks that involve me and the Libelle out hunting for thermals. I also think that since it is such a low cost DLG alternative that I'm more likely to to be aggressive with this plane.
The Dream-Flight Libelle is a winner in my book and just what I was waiting for someone to produce!
Dream-Flight is a small family-run business based in Goleta, California. Known as the "Goodland," this coastal community offers a variety of soaring conditions.
Dream-Flight's goal is to create unique aircraft that are pure fun to fly. They focus on beginners through experts. Their passion is creating quality, affordable R/C aircraft that get more people outdoors to enjoy the wind and sun.
|Dream-Flight Libelle DLG- Get Out and Glide (2 min 5 sec)|
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Cool||Dream-Flight Libelle DLG||MattyB||Slope||1646||Yesterday 06:22 PM|
|News||Dream-Flight Libelle - DLG||Jim T. Graham||Hand Launch||2192||Apr 15, 2015 10:28 AM|
|Wanted||dream-flight Libelle||rarner||Aircraft - Sailplanes (FS/W)||3||Nov 03, 2014 12:37 PM|
|Discussion||http://www.dream-flight.com/files_download/Libelle.pdf||hellmansam||Hand Launch||35||Mar 30, 2014 09:03 PM|
|Build Log||Dream-Flight “Libelle” Build and Maiden flights, check in here.||Tspin||Slope||8||Mar 07, 2014 07:50 PM|