Just gave it a quick test in the cart barn...wow! It's the smoothest most powerful motor I've flown with and I've tested every motor possible including Hacker. Can't wait to get an outdoor flight tonight on the golf course.

Originally Posted by hone1er

Thanks! Yes, That was with the stock power combo and gens ace 3s 1550s. I've also flown the plane on 3s 2100 packs but i prefer something a little smaller. 1500-1800mah will give the most float

I picked out the 78g for a little more power, hopefully it'll work out. I also got four 3s 1600mAh 40C sky lipos! I'm kinda excited.

I have been experimenting with the Twisted Hobbys 24g motor on the Crack Yak and Pitts bipe.
Tried the following combinations:

1) 2S and 8x4.3 prop
2) 2S and 9x4.7 prop
3) 3S and 8x4.3 prop
4) 3S and 9x4.7 prop

For slow and floaty flying, the 2S and 9x4.7 is the ticket.
For not as slow and floaty flying, but a lot more power, the 3s and 9x4.7 is the ticket.

However, I have read where running 3S with the 9x4.7 prop will smoke the 24g TH motor. Is this true? If so, what 9" prop can be used? Just don't care for the 8x4.3 on 2S or 3S....

Originally Posted by STLAV8R

I have been experimenting with the Twisted Hobbys 24g motor on the Crack Yak and Pitts bipe.
Tried the following combinations:

1) 2S and 8x4.3 prop
2) 2S and 9x4.7 prop
3) 3S and 8x4.3 prop
4) 3S and 9x4.7 prop

For slow and floaty flying, the 2S and 9x4.7 is the ticket.
For not as slow and floaty flying, but a lot more power, the 3s and 9x4.7 is the ticket.

However, I have read where running 3S with the 9x4.7 prop will smoke the 24g TH motor. Is this true? If so, what 9" prop can be used? Just don't care for the 8x4.3 on 2S or 3S....

Yeah use the 9x4.7 on 2S.

+





=

Which Causes This

:

And if you want to know why, Watch this:

Let's Roll - Starring the 48' EPP Sbach 342 from Twisted Hobbys (1 min 7 sec)

Brad,
The new carbon fiber servo arm extensions are a great addition to your product line-up. Very well made, pre drilled holes lined up perfectly to the Tower Pro arm’s holes and as you can see it brought out the “crazy” in the Sbach. ( I like crazy)

These extension arms would be great for anyone looking to increase your control surface throw in the larger Telink or RC Factory products.

That is some ridiculous aileron throw

Originally Posted by RCAddict16

That is some ridiculous aileron throw

You do mean ridiculously good…Right?

What do you think

Originally Posted by RCAddict16

What do you think

I try not to

I can't help not thinking (too dumb) haha jk

Dear Brad, please send this kid everything he needs to get this plane in the air. More time flying less time posting.

Originally Posted by RCAddict16

Yeah use the 9x4.7 on 2S.

So the motor will be toast with the 9x4.7 on 3S?

Originally Posted by STLAV8R

So the motor will be toast with the 9x4.7 on 3S?

Pretty much haha

Redoing some hinging on my Extra slick, using Blenderm at the moment.

Should i be closing that gap between the points of the two beveled edges or leaving a gap? 1/16"? 1/32"?

I assume Blenderm is an acceptable hinge replacement over Welder's, I have trouble getting the Welder's thin enough.

Originally Posted by RCAddict16

Pretty much haha

Looks like I will stick with 2S on the 9x4.7.