sorry it is with walkera firmware right now, to delete it can i use the walkera dfu tool, or do i use a different one? Ive tries the regular firmware upgrade to no avail but I havent tried to manually delete the library file first.

Thanks

You don't have to delete anything from the transmitter, just the devo 10 firmware and library dfu files on your computer that you downloaded from walkera. Then re-download them from the Walkera site. Then try upgrading again.

What has happened is the library dfu file on your computer has become corrupted from clicking upload. If you want to double check, the devo-10 lib v0.2.dfu file should be 267Kb on your computer. If it is larger, it means the library from the transmitter has been added to it and it will not work.

Originally Posted by djrocketodd

sorry it is with walkera firmware right now, to delete it can i use the walkera dfu tool, or do i use a different one? Ive tries the regular firmware upgrade to no avail but I havent tried to manually delete the library file first.

Thanks

Originally Posted by djrocketodd

sorry it is with walkera firmware right now, to delete it can i use the walkera dfu tool, or do i use a different one? Ive tries the regular firmware upgrade to no avail but I havent tried to manually delete the library file first.

Thanks

What kind of battery do you have in? LiPO or NiMH or regular AA?

My 8S did this when I used a lipo pack, and the symptom went away when I went back to AA's.

Rafa

Originally Posted by djrocketodd

I have this problem:

I have the walkera DEVO 10 when I turn on the unit it beeps and i get a saving please wait message, then it goes blank and does the same thing again, about 1 second between beeps, here is a photo of the screen, I've tried switched in different positions, ive tried updating firmware, downgrading firmware and nothing works.

Any Ideas???? please help

Can this be fixed somehow on my end with reprogramming it or something of the sort?

I have a question here will dsm2 with sbus receiver work? I was thinking of use on Autoquad 6 beta flight controller

Here's a buddy code for a nicely dimensioned life battery for my Devo 8: http://www.hobbyking.com/buddy.asp?c...A-553A7A75E1B7

Originally Posted by itsmillertime

Here's a buddy code for a nicely dimensioned life battery for my Devo 8: http://www.hobbyking.com/buddy.asp?c...A-553A7A75E1B7

That won't fit in devo8.
Change that to the 1700 instead.

Regards
Paul

It'll fit in mine. There's a tray that holds the 4 AA holder in and once removed there is a lot more room. Additionally I trimmed it out even more. I thought if I were to go to a lipo it'b be a life which is closest to 4 AA's 6 volts and try to get as close to the AA's capacity as possible.

what if you remove the 4cell battery cage? i removed it in mine and i can get 1300 mah lipo in...

Originally Posted by itsmillertime

It'll fit in mine. There's a tray that holds the 4 AA holder in and once removed there is a lot more room. Additionally I trimmed it out even more. I thought if I were to go to a lipo it'b be a life which is closest to 4 AA's 6 volts and try to get as close to the AA's capacity as possible.

Ok strange I have that one and I can't make it fit.
Please post a picture.

I have this battery:

http://www.hobbyking.com/hobbyking/s...arehouse_.html

It doesn't quite fit, the lid would have to go down another 1mm to latch. I just put a piece of tape on it though. Also I did grind out the little ridge of plastic that runs up the middle of the compartment.

Yours is short and fat whereas mine is long and skinny, lol.

I just use Rechargeable NiMH AA batteries. Last a good while don't have to pull out to charge, just use charge jack on TX. I use an old Futaba TX/RX charger that has a red LED on it which lights up when charging. It puts out around 200ma if I remember right. Also remember reading NiMH batteries don't have a memory problem.

Yeah I used to use energizer recharge NiMH's. But I started to not like them since they take 8 hours to charge, and it seemed like I had to babysit them while charging, for some reason they would get really hot in the Energizer charger. I realize some heat is normal but I don't think they should be getting hot enough to burn my skin.

So i went away from those, and got this 11 dollar pack I can charge in 45 min. Plus with the LiPoFe4 pack the screen is a bit brighter.

Quick question for someone who has original walkera firmware on their transmitter.

What happens if you cycle the tx off and back on after the model is bound and working? Will it re-bind after the tx is rebooted? Or does the rx just do a slow flash?