HobbyKing.com New Products Flash Sale
Reply
Thread Tools
This thread is privately moderated by billpa, who may elect to delete unwanted replies.
Old Sep 05, 2012, 08:06 AM
Registered User
McLean, VA
Joined Dec 2001
289 Posts
Brushed Motor Fwd and Rev Question

First time Eagtree user with V4

Searching forum returned no results, so hopefully one of you can help.

I want to install the logger in a boat that has a brushed motor and an ESC that allows forward and reverse. The V4 instructions specify the motor side red wire should connect to the positive pole on the motor. That pole becomes negative in reverse direction.

How will the V4 react? I am just logging VOLTS, AMPS, and MAH values. Will I get absolute totals or subtractions.......or a puff of smoke?

The boat has a car type motor and runs on a 2S-4900 mah Lipo.

Thanks for any advice or warnings!

Jim
Jim Blanchfield is offline Find More Posts by Jim Blanchfield
Reply With Quote
Sign up now
to remove ads between posts
Old Sep 05, 2012, 04:26 PM
billpa's Avatar
Joined Nov 2003
4,936 Posts
HI Jim,

The eLogger should connect between your battery and your ESC, not between your ESC and your motor.

I searched the manual for the word "motor" and didn't find anything re connecting the red wire to the motor side. Could you let me know where in the manual you are seeing that? We need to correct if it it's there.
billpa is offline Find More Posts by billpa
Site Sponsor
Reply With Quote
Old Sep 05, 2012, 05:51 PM
Registered User
McLean, VA
Joined Dec 2001
289 Posts
billpa,

Thank you for the prompt reply.

I did not read the instructions as carefully as I should have.

On page 2, last paragraph......."The red wires of the 'wire lead' version of the eLogger must be connected to the positive side of the load and source (normally the red wires). For measuring current and voltage during battery charging, it is ok to connect a charger to the ES connection, so that current is flowing 'backwards' through the eLogger. The eLogger will still measure current correctly in this mode!"

I mistakenly mistook "load" to mean the motor. The subsequent mention of current flowing "backwards" through the eLogger being ok made me wonder whether the mah would be subtracted from a prior total, and whether volts and amps would be graphed as negative values.

After seeing your reply, its now clear that with the eLogger between the ESC and battery, current will be flowing only in one direction, regardless of the motor's rotational direction.

I do have Sermos connectors between the ESC and the motor and between the ESC and the battery. But it would have been an error if I had put the eLogger between the ESC and the motor.

Thanks for the great customer support. Sorry about raising a silly question.

Jim

PS....is the "ES connection" in line 3 of my quote supposed to be "ESC connection"
Jim Blanchfield is offline Find More Posts by Jim Blanchfield
Reply With Quote
Old Sep 09, 2012, 12:29 AM
Registered User
junioro16v's Avatar
Brazil, PR, Curitiba
Joined Mar 2009
320 Posts
Quote:
Originally Posted by Floater73 View Post
Bill,

Is there a way to get the points type kmz file from the elogger? Like this one.

http://www.rcgroups.com/forums/showp...postcount=8227

Steve
Bill,

Any news on that or something similar to this?
junioro16v is offline Find More Posts by junioro16v
Reply With Quote
Old Sep 12, 2012, 09:46 AM
Registered User
junioro16v's Avatar
Brazil, PR, Curitiba
Joined Mar 2009
320 Posts
Quote:
Originally Posted by junioro16v View Post
Bill,

Any news on that or something similar to this?
Still waiting for any answer.
junioro16v is offline Find More Posts by junioro16v
Reply With Quote
Old Sep 14, 2012, 11:26 AM
Registered User
junioro16v's Avatar
Brazil, PR, Curitiba
Joined Mar 2009
320 Posts
Well, well.
Good support here Bill.
junioro16v is offline Find More Posts by junioro16v
Reply With Quote
Old Sep 14, 2012, 02:38 PM
billpa's Avatar
Joined Nov 2003
4,936 Posts
Hi, sorry, I missed your post when I was last here.

I like the look of the points - had not seen that before. It's something we can look into doing. Any other interest?
billpa is offline Find More Posts by billpa
Site Sponsor
Reply With Quote
Old Sep 14, 2012, 04:59 PM
But often down to earth
Floater73's Avatar
Oklahoma, USA
Joined Sep 2010
736 Posts
Quote:
Originally Posted by billpa View Post
Hi, sorry, I missed your post when I was last here.

I like the look of the points - had not seen that before. It's something we can look into doing. Any other interest?
I would like it.

Steve
Floater73 is offline Find More Posts by Floater73
Reply With Quote
Old Sep 14, 2012, 05:37 PM
Registered User
junioro16v's Avatar
Brazil, PR, Curitiba
Joined Mar 2009
320 Posts
Quote:
Originally Posted by Floater73 View Post
I would like it.

Steve
Anything like this or close to this is very good. I think this way you can see more clearly the track. High altitudes with red colors or anything like this.
junioro16v is offline Find More Posts by junioro16v
Reply With Quote
Old Oct 15, 2012, 11:59 AM
Registered User
junioro16v's Avatar
Brazil, PR, Curitiba
Joined Mar 2009
320 Posts
Quote:
Originally Posted by junioro16v View Post
Anything like this or close to this is very good. I think this way you can see more clearly the track. High altitudes with red colors or anything like this.
Bill,

Any news on that request?
junioro16v is offline Find More Posts by junioro16v
Reply With Quote
Old Oct 16, 2012, 03:12 PM
billpa's Avatar
Joined Nov 2003
4,936 Posts
Hi Junior,

This is on our list of things to dig into. The developer here who does this is on another project, but I hope we'll be able to dig into it soon.
billpa is offline Find More Posts by billpa
Site Sponsor
Reply With Quote
Old Dec 03, 2012, 09:50 PM
Registered User
Joined May 2004
556 Posts
I'm considering one of these on a 10S 3000W system. With all the chatter about avoiding long battery leads, does the V4 introduce enough inductance that I should worry about my ESC? Do the Hall sensors take all my problems away......
Sit-N-Fly is offline Find More Posts by Sit-N-Fly
Reply With Quote
Old Dec 12, 2012, 03:22 PM
billpa's Avatar
Joined Nov 2003
4,936 Posts
Hi, I would be surprised if the eLogger introduced enough inductance to cause you any issues. The resistance through the hall sensor itself is approximately 0.0001 ohm, if that helps.
billpa is offline Find More Posts by billpa
Site Sponsor
Reply With Quote
Old Dec 17, 2012, 07:44 PM
Registered User
junioro16v's Avatar
Brazil, PR, Curitiba
Joined Mar 2009
320 Posts
Any news?
http://www.rcgroups.com/forums/showp...&postcount=154
junioro16v is offline Find More Posts by junioro16v
Reply With Quote
Old Dec 18, 2012, 02:33 PM
billpa's Avatar
Joined Nov 2003
4,936 Posts
Hi, we have that feature on our UI request list, but have not gotten to it yet.
billpa is offline Find More Posts by billpa
Site Sponsor
Reply With Quote
Reply


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Question OSD Pro, eLogger V3, GPS V4 problems updating firmware in OSD Pro jbfoamy Eagle Tree Systems 23 Jun 02, 2012 03:59 PM
New Product Announcing the eLogger V3! billpa Eagle Tree Systems 281 Aug 30, 2011 02:20 PM
Cool Announcing the eLogger V3! billpa Product Announcements 21 Nov 06, 2007 12:28 PM
Discussion Announcing the MicroPower V3 eLogger! billpa Power Systems 2 Oct 10, 2007 07:22 PM