SMALL - espritmodel.com SMALL - Telemetry SMALL - Radio
Reply
Thread Tools
Old Yesterday, 02:39 PM
Yet another flying K1W1
41south's Avatar
Wellington, New Zealand
Joined Jan 2006
511 Posts
And over at Multiwii
41south is online now Find More Posts by 41south
Reply With Quote
Sign up now
to remove ads between posts
Old Yesterday, 03:33 PM
New Nemesis Owner
United States, MO, KCMO
Joined Jun 2014
314 Posts
Quote:
Originally Posted by Invid View Post
thanks
OldManJ is online now Find More Posts by OldManJ
Reply With Quote
Old Yesterday, 07:33 PM
Registered User
Nora's Avatar
Joined Aug 2014
26 Posts
Quote:
Originally Posted by cosmic2112 View Post
How about this:-

http://www.multiwii.com/wiki/?title=Flightmodes

Multiwii and Naze share a lot in common.
Thanks
Nora is offline Find More Posts by Nora
Reply With Quote
Old Today, 04:37 AM
Professional UAV Services
Redemptioner's Avatar
Australia
Joined Dec 2009
2,412 Posts
Quick question gents.

Current firmware running on Naze32 acro, can't seem to get the RC input mapping to work. I have tried via the GUI and via CLI and in both cases they clearly show the right mapping (mode 4 so yaw and roll swapped) but the board does not have any change when you go to use it. Never had an issue in the past with other boards and tried re-flashing multiple times (slow, full chip erase etc) and still the same. And yes I understand I can change the mapping on the Taranis but this would mean I would have to remember that the setup is "different" and which board has the issue......

So has this feature been broken due to the upgrade in the GUI/firmware when JR & Futaba mapping was added?
Redemptioner is offline Find More Posts by Redemptioner
Reply With Quote
Old Today, 04:48 AM
Registered User
Boris B's Avatar
The Netherlands
Joined May 2012
765 Posts
Quote:
Originally Posted by Redemptioner View Post
Quick question gents.

Current firmware running on Naze32 acro, can't seem to get the RC input mapping to work. I have tried via the GUI and via CLI and in both cases they clearly show the right mapping (mode 4 so yaw and roll swapped) but the board does not have any change when you go to use it. Never had an issue in the past with other boards and tried re-flashing multiple times (slow, full chip erase etc) and still the same. And yes I understand I can change the mapping on the Taranis but this would mean I would have to remember that the setup is "different" and which board has the issue......

So has this feature been broken due to the upgrade in the GUI/firmware when JR & Futaba mapping was added?
What cli command are you using to swap those?
Boris B is online now Find More Posts by Boris B
Reply With Quote
Old Today, 05:10 AM
Professional UAV Services
Redemptioner's Avatar
Australia
Joined Dec 2009
2,412 Posts
the usual
map AETR4231
Redemptioner is offline Find More Posts by Redemptioner
Reply With Quote
Old Today, 10:54 AM
Registered User
United States, CA, Auburn
Joined Jan 2009
723 Posts
any one here have the rctimer mini hex?..the argonaut ?
pinoydad is online now Find More Posts by pinoydad
Reply With Quote
Old Today, 05:21 PM
Registered User
Joined Aug 2013
45 Posts
I am having some problems with the Battery Voltage.

They were set to 3.5 and 4.3v and sometimes they are set to 0.3v and 0.4v so I over-discharge my lipo.
Happend now a couple of times with two differnt Naze32 acro.
I think there is a software problem.

Are there more information concerning this topic?
usab is online now Find More Posts by usab
Last edited by usab; Today at 05:27 PM.
Reply With Quote
Old Today, 05:39 PM
AMA # 949551
rikybob's Avatar
USA, FL, Orlando
Joined Oct 2009
2,183 Posts
Accck! I made a knee jerk purchase and bought the NAZE32 r4 without the telemetry pins...and I screwed?

All the best!

b
rikybob is online now Find More Posts by rikybob
Reply With Quote
Reply


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
For Sale AfroFlight Flight Controller (Naze32) Box/Container/holder Made from Delrin Greasetattoo Aircraft - Electric - Multirotor (FS/W) 8 Feb 14, 2014 12:03 PM
Help! beginner's guide to Rhino for dummy's ????? grover CAD/CAM 4 Oct 16, 2011 05:56 AM
Help! Guide for sailplane setup & triming Ken Smith Sailplane Talk 4 Sep 13, 2011 02:12 PM
Help! Walkera 4#3 easy setup guid ? dendirk Micro Helis 3 Mar 15, 2008 11:45 AM
Discussion Tips for Red Necks (Like myself.) Don Sims Humor 0 Feb 11, 2002 10:53 PM