Lama400d Help plz

Nico, · Nov 01, 2009, 07:24 PM

Lama 400 d

Hello, sorry that i have place this in the wrong section, i cant place a topic in the coaxiaal section,

i have a problem whit dismounting the flybar connector, is it true that is see a pin in it? how do you get this out,? whit a needle or something?
and how do you prober get the mainblade holders off and on, please help me whit this, i cant get it right,,

Sorry for my english, i am from the netherlands,

Nico, · Nov 03, 2009, 06:32 PM

Somebody plz

Nico, · Nov 03, 2009, 06:33 PM

some body plz?>

airwolf2006 · Nov 03, 2009, 07:08 PM

Just ask your question in the 400D thread in multirotor.

KCV6 · Nov 05, 2009, 08:42 AM

To remove the small pins that hold the blade holders in place, take theblades off, take the fly bar off, undo the two inboard small retaining screws that hold the pins in. tape around the holder and then bind and run the motors up. The pins will fly out into the taped up area.

I actually prefer to remove the shafts and place small bags over the holders and spin them between my fingers.

the flybar is removed by undoing the two small screws in the side of the head and then lifting the flybar and end cap out.

let me know if you need more information. I have done this lots of times.

Mark

Nico, · Nov 05, 2009, 06:56 PM

Hello thankyou for your help,
so i see its, better to remove, de shaft completje.. in place of the connector,? i see a pin it in it but i cant get it out, its verry tiny,
now i am canna try to get the shaft out, but how do you place the pins into the blade holders? whit a pincet doest work i think

Thanks Again! and sorry for my english i hope you understand

KCV6 · Nov 05, 2009, 08:13 PM

Nico,

I will do a writeup and copy it here as well as the 400D modification thread.

Mark

Nov 01, 2009, 07:24 PM	#1
Nico, Registered User Join Date: Nov 2009 Posts: 4	Lama400d Help plz Lama 400 d Hello, sorry that i have place this in the wrong section, i cant place a topic in the coaxiaal section, i have a problem whit dismounting the flybar connector, is it true that is see a pin in it? how do you get this out,? whit a needle or something? and how do you prober get the mainblade holders off and on, please help me whit this, i cant get it right,, Sorry for my english, i am from the netherlands,

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Question Triton Eq Plz Help Me ...	fearlesshugo	Batteries and Chargers	5	Sep 19, 2009 08:47 PM
Help! can is use 25A ESC for FC 28-12 brushless motor 1534kv? PLZ help me	munsaf	Electric Motor Design and Construction	2	Sep 16, 2009 09:09 AM
Discussion eflite charger won't charge my pack. Beeps error. Help a noob plz	CarComp	Batteries and Chargers	8	Sep 06, 2009 03:26 PM
Discussion plz plz plz tell me [snap rings]	LikWydd	Fuel Heli Talk	3	Nov 17, 2006 10:11 PM
Please Someone Help Me Plz Plz	Eeeeky	Aircraft - Electric - Helis (FS/W)	7	Mar 30, 2005 02:49 PM

Nov 03, 2009, 06:32 PM	#2
Nico, Registered User Join Date: Nov 2009 Posts: 4	Somebody plz

Nov 03, 2009, 06:33 PM	#3
Nico, Registered User Join Date: Nov 2009 Posts: 4	some body plz?>

Nov 03, 2009, 07:08 PM	#4
airwolf2006 Wish my coax could autorotate Join Date: Aug 2009 Location: Riverdale Md. Posts: 814	Just ask your question in the 400D thread in multirotor.

Nov 05, 2009, 08:42 AM	#5
KCV6 Registered User Join Date: Aug 2009 Location: Adelaide Australia Posts: 427	To remove the small pins that hold the blade holders in place, take theblades off, take the fly bar off, undo the two inboard small retaining screws that hold the pins in. tape around the holder and then bind and run the motors up. The pins will fly out into the taped up area. I actually prefer to remove the shafts and place small bags over the holders and spin them between my fingers. the flybar is removed by undoing the two small screws in the side of the head and then lifting the flybar and end cap out. let me know if you need more information. I have done this lots of times. Mark

Nov 05, 2009, 06:56 PM	#6
Nico, Registered User Join Date: Nov 2009 Posts: 4	Hello thankyou for your help, so i see its, better to remove, de shaft completje.. in place of the connector,? i see a pin it in it but i cant get it out, its verry tiny, now i am canna try to get the shaft out, but how do you place the pins into the blade holders? whit a pincet doest work i think Thanks Again! and sorry for my english i hope you understand

Nov 05, 2009, 08:13 PM	#7
KCV6 Registered User Join Date: Aug 2009 Location: Adelaide Australia Posts: 427	Nico, I will do a writeup and copy it here as well as the 400D modification thread. Mark