Neu motor mount for Enigma

Synth · Nov 05, 2009, 03:36 AM

Iv'e seen some nice motor mounts for Neu 1500 6.7-1 For F5b ships. Does someone have one to sell that would fit an Enigma? I have limited tools to make a proper one. Please pm. if you have something that would work for me.

Thanks,
Ron.

aldenca · Nov 05, 2009, 12:01 PM

I recently had a nice cnc carbon fiber motor mount that I had purchased break in a 3 meter Trinity. I have another of these mounts in my Enigma. They look great and feel great but I don't know that they have the best design. Mine was made from two pieces(front and back) glued together. It was made like this so the screws were completely recessed and the two pieces were different diameters to fit the tapered nose of the plane.
However if these pieces come apart which they did in mine (they seemed to be glued) then you onlyhave half the width of the mount glued to the plane. The screws don't contact the front 50 percent of the mount so the motor is not attached here either. I don't know if I explained this well but I have a few of these premade mounts. I would have prefered the screws not be recessed at all(you dont need this if you recess the whole mount). You can get appropriate sized hole-drilling attachments that help a lot with aircraft grade laminted wood.

grobbins666 · Nov 05, 2009, 02:06 PM

I bought one from this guy. Expensive but well worth it.
http://www.rcgroups.com/forums/showthread.php?t=1047261
Mine did not fit... it was to big, but that is because the enigma are molded but the reenforcement is done by hand. Just used a drill and a file to slim it down a little. Perhaps you can measure with a caliper and custom order one.

Gregory

Synth · Nov 05, 2009, 03:02 PM

Thanks guys.

la528it · Nov 05, 2009, 04:04 PM

Ron, I can make you one, but it will not have nice cooling vents. It will, however be made of two sheets of carbon stock.. I'll post pics tonite, I can put in cooling holes, but I they are not pretty, just assortment of holes. Cost is outrageous, because every one I make takes about a year off of my life... which is why $50 + shipping is actually a deal!

Synth · Nov 05, 2009, 04:49 PM

Quote:

Originally Posted by la528it

Ron, I can make you one, but it will not have nice cooling vents. It will, however be made of two sheets of carbon stock.. I'll post pics tonite, I can put in cooling holes, but I they are not pretty, just assortment of holes. Cost is outrageous, because every one I make takes about a year off of my life... which is why $50 + shipping is actually a deal!

Thanks Richard but I'll pass on that one. Just a little rich for my blood. Yup, the carbon stuff is pretty tough on the system. Hmmm, $50.00 for 1 year doesn't make your life worth much huh.

Dbox · Nov 05, 2009, 04:54 PM

One year of mine

Yuri.

la528it · Nov 05, 2009, 05:45 PM

Quote:

Originally Posted by Synth

Thanks Richard but I'll pass on that one. Just a little rich for my blood. Yup, the carbon stuff is pretty tough on the system. Hmmm, $50.00 for 1 year doesn't make your life worth much huh.

No, but I live dangerously (expected cost of one less year of life by time carbon dust catches up to me is $50)

Nov 05, 2009, 03:36 AM	#1
Synth earth belowus drifting falling Join Date: Feb 2003 Location: Victoria B.C. Canada Posts: 1,345 Trader Rating: 71	Neu motor mount for Enigma Iv'e seen some nice motor mounts for Neu 1500 6.7-1 For F5b ships. Does someone have one to sell that would fit an Enigma? I have limited tools to make a proper one. Please pm. if you have something that would work for me. Thanks, Ron.

Nov 05, 2009, 12:01 PM	#2
aldenca Registered RC Addict Join Date: Jan 2007 Location: Santa Clara/Milpitas/ Bay Area Posts: 43 Trader Rating: 4	motor mount I recently had a nice cnc carbon fiber motor mount that I had purchased break in a 3 meter Trinity. I have another of these mounts in my Enigma. They look great and feel great but I don't know that they have the best design. Mine was made from two pieces(front and back) glued together. It was made like this so the screws were completely recessed and the two pieces were different diameters to fit the tapered nose of the plane. However if these pieces come apart which they did in mine (they seemed to be glued) then you onlyhave half the width of the mount glued to the plane. The screws don't contact the front 50 percent of the mount so the motor is not attached here either. I don't know if I explained this well but I have a few of these premade mounts. I would have prefered the screws not be recessed at all(you dont need this if you recess the whole mount). You can get appropriate sized hole-drilling attachments that help a lot with aircraft grade laminted wood.

Nov 05, 2009, 02:06 PM	#3
grobbins666 Registered User Join Date: Jul 2008 Location: Huntington Beach So. Cal Posts: 170 Trader Rating: 3	firewall I bought one from this guy. Expensive but well worth it. http://www.rcgroups.com/forums/showthread.php?t=1047261 Mine did not fit... it was to big, but that is because the enigma are molded but the reenforcement is done by hand. Just used a drill and a file to slim it down a little. Perhaps you can measure with a caliper and custom order one. Gregory

Nov 05, 2009, 04:54 PM	#7
Dbox One Idiot is plenty... Join Date: Jun 2005 Location: Planet Earth Posts: 2,682 Trader Rating: 65	One year of mine Yuri. Attached Thumbnails 39.8 KB · Views: 26

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Discussion Good 3d flat plate for gws stick mount motor	GWhaling	Parkflyers	3	Nov 01, 2009 03:05 PM
Sold Maddog motor mount for Hacker A60	M Carr	Aircraft - Electric - Power Systems (FS/W)	5	Oct 25, 2009 09:02 PM
Help! Building motor mount for AL Hellen	roach101761	Scale Boats	1	Oct 13, 2009 01:58 PM
Discussion Motor Mount for Neu 1506/1y P32 6.7 Gearbox	JackHiner	Power Systems	5	Jul 20, 2009 07:38 PM
For Sale Cambria Motor Mount for Neu 151x series and P32 gearbox	JPHen	Aircraft - General - Miscellaneous (FS/W)	1	Mar 11, 2009 11:12 AM

Nov 05, 2009, 03:02 PM	#4
Synth earth belowus drifting falling Join Date: Feb 2003 Location: Victoria B.C. Canada Posts: 1,345 Trader Rating: 71	Thanks guys.

Nov 05, 2009, 04:04 PM	#5
la528it Registered User Join Date: Dec 2007 Location: City of Angels Posts: 803 Trader Rating: 52	Ron, I can make you one, but it will not have nice cooling vents. It will, however be made of two sheets of carbon stock.. I'll post pics tonite, I can put in cooling holes, but I they are not pretty, just assortment of holes. Cost is outrageous, because every one I make takes about a year off of my life... which is why $50 + shipping is actually a deal!