RC Groups

RC Groups
    3D Flying
        Discussion 3D Training Videos

#1 AirBorne_AZ Dec 28, 2007 08:48 PM

3D Training Videos
 
Hello All,

Lets dedicate this thread to a collection of links to training videos, specifically the ones with stick overlays. Once fully populated, this thread will serve as one stop for learning 3D maneuvers.

Lets share our collection of links to 3D learning videos.

Here is a collection of my links:

http://www.privateradio.org/7channels/

How to Lomcevak (4 min 8 sec)


http://www.teamflyingcirkus.com/ (You would need to create an account, and once logged in, go to Media Center-->3D University)

http://www.flyinggiants.com/
http://www.flyinggiants.com/content/groundschool.aspx



AirBorne_AZ

#2 Malves Dec 29, 2007 02:11 AM

Blender, KE Spin, KE circles, Flat spins (inverted and upright), Harrier, Inverted Harrier, Hover, Rolling Harrier (both ways), High Alpha KE, Snap roll, Slow roll, Waterfall, Tumbling.

You can find the first 3 here http://www.rcgroups.com/forums/showthread.php?t=786514, and the remaining videos here

#3 Coonak Jan 06, 2008 08:18 AM

These would have to be my fav instructional vids.
Learnt heaps from em!

Rolling harrier how to with sticks overlay!
Mark Leseberg Instructional Vid

Plane setup with Andrew Jesky is another great vid!
Andrew Jesky Instructional Vid

Andrew Jesky Mixing Instructional

Cheers

Mick

#4 earlybird2 Jan 08, 2008 01:16 AM

Great idea.

Ben

#5 jonnyjetprop Feb 11, 2008 10:39 AM

http://www.3dhobbyshop.com/HowToFly3DVids.htm

John

#6 hot glue Feb 18, 2008 10:17 AM

Hangar 9's FS1 has quite a few training videos that i like to watch.

#7 jrubenis Feb 20, 2008 01:31 PM

Ok i am new to 3d and need someone to explain the moves for me. Not how to do them but the names. I know knife edges harrier torque rolls but what are benders and KE benders?? And waterfalls? I have looked on youtube for some vids but dont know which moves are called what Thanks.

#8 hot glue Feb 20, 2008 03:23 PM

Quote:

Originally Posted by jrubenis
Ok i am new to 3d and need someone to explain the moves for me. Not how to do them but the names. I know knife edges harrier torque rolls but what are benders and KE benders?? And waterfalls? I have looked on youtube for some vids but dont know which moves are called what Thanks.

The blender is where you come in a dive while rolling and put it into a inverted flat spin. A water fall is where you hover and apply full throttle and do a outside loop and get into a hover again.

#9 jrubenis Feb 20, 2008 03:40 PM

Thanks. I have found a site which shows pictures and names of the moves. One last thing. It says full down elevor,after the roll and rudder for the blender, is that full down stick (ele up) or actual elevator down (stick up)???

Found all these on WWW.YOUTUBE.COM just do a search for RC TRAINING and it has all the moves, with stick overlay, as done on a simulator.

#10 hot glue Feb 20, 2008 03:44 PM

Quote:

Originally Posted by jrubenis
Thanks. I have found a site which shows pictures and names of the moves. One last thing. It says full down elevor,after the roll and rudder for the blender, is that full down stick (ele up) or actual elevator down (stick up)???

I dont understand. Whats your question. Do you have a sim. to practice on?

#11 jrubenis Feb 20, 2008 03:54 PM

Yeah i have aerofly, but a broken hand means i cant hold controler properly. I was reading a "walkthough" about some 3d moves and it often says full down/up elevator. I wasnt sure if it mean elevator stick down or up,,OR the elevator physically goes up down as they are opposite. To go up, for ex, stick goes down. elevator goes up..hope thats clearer.

#12 hot glue Feb 20, 2008 03:57 PM

Ohhh. It means up/down on the plane. So if it said up, pull down on the stick.

#13 jrubenis Feb 26, 2008 02:50 PM

http://www.troybuiltmodels.com/AwesomePilot.htm
great site for beginners and experts

#14 BeerBatter Feb 27, 2008 08:27 PM

Do you have to be registered to Flying Giants to view the Andrew Jesky videos; access denied for me.

#15 Vitter Feb 28, 2008 12:09 AM

Quote:

Originally Posted by BeerBatter
Do you have to be registered to Flying Giants to view the Andrew Jesky videos; access denied for me.

yes :D register

Vitter


All times are GMT -5. The time now is 11:33 AM.