RC Groups

RC Groups
    Radios
        Help! Futaba 10CG Servo End Point help needed

#1 Rick~K Oct 02, 2012 05:59 PM

Futaba 10CG Servo End Point help needed
 
Hello Everyone,

I need a little help on adjusting my "End Points" on my radio. I can find all the main channel adjustments but not on the Aux-Ch's, I have one of my Ch's set up on the lever switch (VR (E) ) but can't find where to adjust it, I've looked in the manual also. I can find them for the toggles and sticks but not knobs and lever switches.
Thanks!

#2 krysta Oct 03, 2012 09:52 AM

Are you in 7ch mode or 10ch mode in your transmitter?


Sincerely,
Krysta
Product Development & Support Specialist
Futaba Service Center USA
service@futaba-rc.com

Quote:

Originally Posted by Rick~K (Post 22896335)
Hello Everyone,

I need a little help on adjusting my "End Points" on my radio. I can find all the main channel adjustments but not on the Aux-Ch's, I have one of my Ch's set up on the lever switch (VR (E) ) but can't find where to adjust it, I've looked in the manual also. I can find them for the toggles and sticks but not knobs and lever switches.
Thanks!


#3 Rick~K Oct 03, 2012 10:01 AM

Quote:

Originally Posted by krysta (Post 22901896)
Are you in 7ch mode or 10ch mode in your transmitter?


Sincerely,
Krysta
Product Development & Support Specialist
Futaba Service Center USA
service@futaba-rc.com

I'm not sure, it shows 8 ch in window and am able to adjust "gear" and toggle sw, just not levers or knob

#4 krysta Oct 03, 2012 12:29 PM

On the main screen in the upper right hand corner directly below 2.4G, it should say either 7ch or 10ch.

But either way, in either 7 or 10 channel, when you go into the End point screen, toggle down to your Aux channel, it should show L or H, if you have that channel set to a dial. You should then be able to turn the appropriate dial or move the appropriate slider to adjust both sides of the end points.

What are they set to in your Aux channel menu?

Also, have you tried going into a blank model to see if you can set the end points in a completely new model?


Sincerely,
Krysta
Product Development & Support Specialist
Futaba Service Center USA
service@futaba-rc.com

Quote:

Originally Posted by Rick~K (Post 22901974)
I'm not sure, it shows 8 ch in window and am able to adjust "gear" and toggle sw, just not levers or knob


#5 pilotpete2 Oct 03, 2012 02:08 PM

Rick,
Are you trying to use either channel 9 or 10 for this function? These channels do not have an endpoint or sub-trim adjustment, as they're only switched on/off channels.
Pete

#6 Rick~K Oct 03, 2012 02:51 PM

Ok, That worked.. Thanks!!! I was setting my Ch8 that was Aux8 on end point adjustment. I was thinking that was one of my NAZA gain adjustment ch's but they are Ch6&7. I'm new to this radio, my first Futaba since my J series in the 80's and I'm using it for UHF... love the Radio.
Thanks Again Krysta and Pete!

#7 Rick~K Oct 09, 2012 04:51 PM

Krysta, or anyone

Is there a way to disable 2.4 transmit on the 10CG? I'm using it for EZUHF and the manual for UHF says to disable the transmitter (10CG) so both UHF and 2.4 is not transmitted at the same time.

Thanks!

#8 pilotpete2 Oct 09, 2012 05:53 PM

It's covered on page 17 of the manual. It's the option just below the range test power down option;)
Pete

#9 Rick~K Oct 09, 2012 05:54 PM

Quote:

Originally Posted by pilotpete2 (Post 22957228)
It's covered on page 17 of the manual. It's the option just below the range test power down option;)
Pete

Thank You Pete!


All times are GMT -5. The time now is 10:09 AM.