RC Groups

RC Groups
    Hitec/Multiplex USA
        Discussion Eclipse 7 (72 Mhz) FunCub Flaps program

#1 bubbleman Sep 16, 2012 08:16 AM

Eclipse 7 (72 Mhz) FunCub Flaps program
 
Help,

I need a way to slave a second channel to the CH 6 control. The FunCub requires that one flap servo be reversed.

Anton

#2 A.T. Sep 16, 2012 03:12 PM

1 Attachment(s)
Quote:

Originally Posted by bubbleman (Post 22746884)
Help, I need a way to slave a second channel to the CH 6 control. The FunCub requires that one flap servo be reversed. Anton

Given the numerous set ups for one of those models, would need to know how other channels
are being used and which are still free.
All knowledge on mixes is available under:
Hitec Eclipse & Eclipse 7 Pro - All Manuals, Addenda, Quick Setup, CCPM and Additional Programming FAQ

However, rather than trying to slave a second channel, there are also several other methods to install
your MPX Funcub as shown on previous thread:
. Multiplex Easy Cub & Fun Cub - Aileron, Elevator & Flaps Installation
quote"
. Multiplex Easy Cub & Fun Cub - Install Aileron & Elevator - Video
note re video - see pic attached.
"Easiest general purpose solution:
"Multiplex Easy Cub & Fun Cub - Install Aileron & Elevator - Video"
. 3.35 minutes into video is highlighted "Flap Servos on a "Y" Connector".
This describes enlarging one hole sideways so as to flip the servo over and
mount flap horn further over to compensate, refer attached screenshot..
. Size the section of wing to be removed so as to glue as a filler in the original hole.

. Multiplex Easycub questions thread.
. Multiplex Easy/Fun Cub Aileron - pictures
. Differential - Mechanical set-up - Correct Dutch roll and Drag. "

This may also be of interest:
MPX Easy/Fun Cub Tailwheel Assembly & Replacement.


and more under
Alan's Hobby, Model & RC FAQ Web Links

Alan T.

#3 bubbleman Sep 16, 2012 07:31 PM

Quote:

Originally Posted by A.T. (Post 22749484)
Given the numerous set ups for one of those models, would need to know how other channels
are being used and which are still free.
All knowledge on mixes is available under:
Hitec Eclipse & Eclipse 7 Pro - All Manuals, Addenda, Quick Setup, CCPM and Additional Programming FAQ

However, rather than trying to slave a second channel, there are also several other methods to install
your MPX Funcub as shown on previous thread:
. Multiplex Easy Cub & Fun Cub - Aileron, Elevator & Flaps Installation
quote"
. Multiplex Easy Cub & Fun Cub - Install Aileron & Elevator - Video
note re video - see pic attached.
"Easiest general purpose solution:
"Multiplex Easy Cub & Fun Cub - Install Aileron & Elevator - Video"
. 3.35 minutes into video is highlighted "Flap Servos on a "Y" Connector".
This describes enlarging one hole sideways so as to flip the servo over and
mount flap horn further over to compensate, refer attached screenshot..
. Size the section of wing to be removed so as to glue as a filler in the original hole.

. Multiplex Easycub questions thread.
. Multiplex Easy/Fun Cub Aileron - pictures
. Differential - Mechanical set-up - Correct Dutch roll and Drag. "

This may also be of interest:
MPX Easy/Fun Cub Tailwheel Assembly & Replacement.


and more under
Alan's Hobby, Model & RC FAQ Web Links

Alan T.

Allen,

Thanks for the well researched answer.

This is not my first FC. I have been flying one for 2 years. Have ail. dif set up mechanically. I had a pair of normal and reverse servos that I used on my flaps.

I have been on the FC thread and know the option of hacking on the wing:(

IMO a high end 7 ch radio that only allows a 4 ch wing to be setup in GLIDER mode is lame:mad:

My old Futaba allows any ch to any ch mix with no switch to flip and the trim is slaved as well.:rolleyes:


The fellow that I am building this for had a "magic Y" servo reverser that he was not using, so I will use it off CH6.

ch assign will be
1 ail
2 ele
3 throt
4 rudder
5 tow release
6 flaps with reverser
7 not used

Anton

#4 A.T. Sep 16, 2012 08:07 PM

Quote:

Originally Posted by bubbleman (Post 22751227)
Allen,
Thanks for the well researched answer.
This is not my first FC. I have been flying one for 2 years. Have ail. dif set up mechanically.
I had a pair of normal and reverse servos that I used on my flaps.
I have been on the FC thread and know the option of hacking on the wing.
IMO a high end 7 ch radio that only allows a 4 ch wing to be setup in GLIDER mode is lame.
My old Futaba allows any ch to any ch mix with no switch to flip and the trim is slaved as well.
The fellow that I am building this for had a "magic Y" servo reverser that he was not using, so I will use it off CH6.
ch assign will be
1 ail
2 ele
3 throt
4 rudder
5 tow release
6 flaps with reverser
7 not used
Anton

Post #2 "Given the numerous set ups for one of those models, would need to know
how other channels are being used and which are still free. "

Mix Ch 6 to Ch 7:
Switch on the Eclipse 7. Depress both left hand Edit buttons at once
to enter the Set Up menu, then select "PMix 1".
Pull top left front switch forward to turn the mix "ON".
Use left or right cursor button to move flashing icon to set MAS to ch 6 and SLV to ch7.
To adjust throw in either direction, move flashing icon to the %,
then rotate knob left & right and adjust percentage.
[This is essential as Ch6 defaults to 30% - adjust ch6 in Set Up menu under "FLPT"]
Early Eclipse 7 did not have an extension on the ch6 knob. In need, drill and insert a small bolt
for easy finger tip operation. (Or acquire the later style knobs)

Alan T.
Alan's Hobby, Model & RC FAQ Web Links

#5 bubbleman Sep 17, 2012 06:00 AM

Quote:

Originally Posted by A.T. (Post 22751521)
Post #2 "Given the numerous set ups for one of those models, would need to know
how other channels are being used and which are still free. "

Mix Ch 6 to Ch 7:
Switch on the Eclipse 7. Depress both left hand Edit buttons at once
to enter the Set Up menu, then select "PMix 1".
Pull top left front switch forward to turn the mix "ON".
Use left or right cursor button to move flashing icon to set MAS to ch 6 and SLV to ch7.
To adjust throw in either direction, move flashing icon to the %,
then rotate knob left & right and adjust percentage.
[This is essential as Ch6 defaults to 30% - adjust ch6 in Set Up menu under "FLPT"]
Early Eclipse 7 did not have an extension on the ch6 knob. In need, drill and insert a small bolt
for easy finger tip operation. (Or acquire the later style knobs)

Alan T.
Alan's Hobby, Model & RC FAQ Web Links

Alan,

Thanks again.

It is the switch to flip part that has me worried. I want to make this idiot proof. The switch in the wrong position will result in only one flap:eek:

Anton


All times are GMT -5. The time now is 04:14 PM.