HobbyKing.com New Products Flash Sale
punkindrublik's blog
Posted by punkindrublik | Dec 12, 2014 @ 06:15 PM | 1,910 Views
Yep. You don't really miss something til it's gone. Well, they're back!

Get em while they're hot!

http://multirotormania.com/32-bit-/2...fly32-pro.html


.
Posted by punkindrublik | Dec 01, 2014 @ 07:28 AM | 2,026 Views
TRI, QUAD and HEX Bundles
Flight Controllers
Frames
MRM and T-Motors!

CHECK EM OUT
HERE!

SHIPPING AS LOW AS $2!

FREE SHIPPING ON ORDERS OVER $100!!


http://multirotormania.com/...Continue Reading
Posted by punkindrublik | Nov 28, 2014 @ 12:48 PM | 1,601 Views
TRI, QUAD and HEX Bundles
Flight Controllers
Frames
MRM and T-Motors!

CHECK EM OUT
HERE!

SHIPPING AS LOW AS $2!

FREE SHIPPING
ON ORDERS OVER $100!!


http://multirotormania.com/
Posted by punkindrublik | Nov 21, 2014 @ 04:53 PM | 1,642 Views
Yup, they've been shipped.
Kick A$$ motors that are butter smooth! Check out the balance test graphics below. It's showing vibration on the X, Y and Z axis of the motors from stopped to full throttle. And yes, those are T-Motors (MN series) and Sunnyskys (X22) in the comparison!

I'll have power charts soon cuz these things have got gobs of it.

Available in less than a week!
multirotormania.com
Posted by punkindrublik | Oct 27, 2014 @ 05:56 PM | 2,937 Views
It's about time, huh?

Fully capable 32 bit board that runs Baseflight, Cleanflight and Harikari beautifully. You might also have heard of these as Flip32s, but the DragonFly is here to stay!

These boards look awesome. Pick one up now at multirotormania.com!

http://multirotormania.com/32-bit-/1...ly32-acro.html

YOUR ORDER SHIPS WITHIN 24 HOURS.

SOLDERING SERVICE IS FREE AND WILL NOT HOLD UP YOUR ORDER.

SHIPPING AS LOW AS $2!!

Posted by punkindrublik | Oct 22, 2014 @ 05:12 PM | 3,117 Views
It's about time, huh?

Fully capable 32 bit board with baro and mag. Runs Baseflight, Cleanflight and Harikari beautifully. You might also have heard of these as Flip32s, but the DragonFly is here to stay!

These boards look awesome. Pick one up now at multirotormania.com!

http://multirotormania.com/32-bit-/9...fly32-pro.html

YOUR ORDER SHIPS WITHIN 24 HOURS.

SOLDERING SERVICE IS FREE AND WILL NOT HOLD UP YOUR ORDER.

SHIPPING AS LOW AS $2!!

Posted by punkindrublik | Oct 16, 2014 @ 06:19 PM | 2,398 Views
Yup, they're now in stock. Introductory price of $19 per motor (it may stay the same price, "introductory" just sounds cool )

GET THEM HERE!

Just a tad bigger than a SunnySky 2204 but puts out over 30% more power! Plus it uses less amps per gram of thrust!

SS 2204 with 5x3 HQ prop on 12.7v full throttle, 6.6a: 240g of thrust
MRM 2204 with 5x3 HQ prop on 12.7v full throttle, 8.2a: 315g of thrust

Factory balanced with Japanese bearings.
And a feature I really like, the c-clip is countersunk, so you don't need a hole or an X-mount. They'll mount to anything flat.

This is one sexy motor!

MRM Mini Titan 2204-2300kv
28g
2-4s
150mm wires
5mm shaft

We'll have specs and charts (and better pictures) up shortly, I just got them an hour ago
http://multirotormania.com/home/171-...ess-motor.html

Yer gonna love em! 1806, 2208, 2212 and 2216 to come!
Posted by punkindrublik | Oct 09, 2014 @ 06:25 PM | 2,714 Views
These just came in today. The classic KK2.1.5 is now available at multirotormania.com!

$25 each and shipped within 24 hours. SAME DAY SHIPPING if ordered early enough!

These boards come preloaded with Steveis V1.18S1 Pro, or V1.17S1 Lite firmware.
A donation to Steveis' favorite charity and Rolf Bakke is provided for each sale!

INCLUDES straight OR 90 pins, plus our FREE SOLDERING SERVICE.
(just make sure you check the option box )

CLICK HERE!!
Posted by punkindrublik | Oct 08, 2014 @ 05:14 PM | 3,043 Views
We've got cool new stuff showing up just about every day

http://multirotormania.com/power-dis...ion-board.html
Posted by punkindrublik | Oct 05, 2014 @ 05:02 PM | 3,498 Views
Here's a sneak peak of what we've got coming this month!
Just a tad bigger than a SunnySky 2204 but puts out over 20% more power!
Factory balanced with Japanese bearings.

MRM Mini Titan 2204-2300kv

Yer gonna love em! 1806, 2208, 2212 and 2216 to come!

multirotormania.com
Posted by punkindrublik | Oct 03, 2014 @ 03:22 AM | 3,978 Views
Check this out!
Our new DragonFly32 Pros are being shipped right now!

multirotormania.com
Posted by punkindrublik | Sep 10, 2014 @ 11:01 PM | 3,606 Views
You heard right. If you need multirotor equipment, be sure to check my new store:

multirotormania.com

I literally just opened the doors last night (9/9). I'm doing a VERY soft opening to make sure that we have everything dialed and will be ready for busier times.

You might recognize quite a few of the products from another popular site out there, but we offer these with my known service and my partner's amazing technical knowledge. PLUS, we will provide UBER FAST SHIPPING, fast e-mail replies and superb support.

SHIPPING AS LOW AS $2!!

LOTS of new products to come, I'm entering them in daily. So please take a gander when ya get a chance.

And feedback is most welcome.

Thanks everybody!

Brian
Posted by punkindrublik | May 30, 2014 @ 10:23 PM | 7,412 Views
200mW 10g
Posted by punkindrublik | Mar 24, 2014 @ 01:22 AM | 8,495 Views
QX-9

Okay, so other than putting some firmware on the OSD (took a little while to realize that's why my picture was funny), this puppy is ready to go. This thing is gonna be a rocket once I switch to 4s.

Plates, tubes and carbon courtesy of awspider (thanks!)
Naze 32 w/GPS
SunnySky 2216-1250s
Afro Slim 20s
FrSky X8-r Rx
Boscam Cobra HD DVR/FPV cam
Boscam 400mW VTx
MinimOSD from WiteSpy
Distribution board with dual BECs (5.5v,12v)
RCTimer 9x5 Carbon Props
Nano-Tech 3300 3s Lipo

AUW 1150g
Posted by punkindrublik | Feb 28, 2014 @ 06:19 AM | 8,602 Views
This is for the few that have shown interest in seeing my new haul.

And yes, I realized after I watched it that I called the NorthStar a "Vortex".

And the one I couldn't remember was the L-19

My Movie (6 min 22 sec)

Posted by punkindrublik | Feb 11, 2014 @ 05:44 PM | 9,120 Views
Just saw this a couple of weeks ago and thought it would be perfect for lipos as it looks like 2 or 3 should stack nicely in a standard aluminum case. At only $8 for two plus fair shipping, I figured I'd share (I bought 4).
Shipped from within the US.

http://www2.pulsetv.com/prodinfo.asp...17&number=5606

As you can see, I can stack 2-4 (depending on batt size) of these loaded with batteries on both sides in a standard aluminum case. The one side I pictured even has room for a few more
Posted by punkindrublik | Oct 04, 2013 @ 02:55 AM | 11,234 Views
I actually finished this months ago, but am just now getting around to posting it. I have a couple more finished projects to post as well.

The first thing I did when I jumped back into this hobby a few months ago, was get me one of them fancy chargin stations I see ya'll got out there. My two 109's in a Tx case with a battery just wasn't cutting it anymore.
So, here's my first completed project during my comeback.

1x 25 amp MeanWell power supply. Hard mounted.
1x 35AH Chrome SLA Battery (not pictured)
2x Astro 109s - I can charge up to 16 amps with this pair. Simple as simple gets. Velcro mounted (the real stuff)
1x Duratrax ICE (soon to be replaced with an Onyx 235). Hard mounted.

Main Board. Hard mounted. Includes -
  • AC/DC/OFF switchable
  • Switches for all chargers with room for more
  • 2x Parallel boards - 7 deans outputs each. Velcro mounted.
  • 2x Astro Blinky balancers - one connected to each board. Velcro mounted.
  • 1x Servo 5/6v tester. Velcro mounted. (later addition, I'll add another pic soon)
  • 1x 5/6v switchable output w/retractable servo lead (male and female)
  • 1x 12v banana plug output
  • Digital voltage readout for PS, DC input and 5/6v output
Fused throughout



When I swap out the Ice for the Onyx, I'll also be adding a LifeSource AC/DC charger and another switch on the main board for it. I decided to go LiFe for my Rx batteries in my gassers and this will give me a quick-charge option for in between flights.
Posted by punkindrublik | Jul 30, 2013 @ 05:24 PM | 20,014 Views
So I don't like taking the cover off to charge my HK 1500mah LiFe packs. I came up with this mod to make charging the battery within the transmitter, so no more battery removal.

PLEASE DO NOT ATTEMPT THIS IF YOU ARE NOT COMPLETELY COMFORTABLE WITH A SOLDERING IRON. You will be working on sensitive electronics and could possibly damage or destroy your transmitter and/or void any warranty.

PROCEED AT YOUR OWN RISK.

That being said, the first thing you need to do is purchase one of these -
http://www.ebay.com/itm/320715057097

It say's 9.6 volt in the ad, but I was informed that this is the correct charger for a 3-cell LiFePO4 pack. I tested this unit with a charge on my pack and it successfully charged to 10.9v and then shut off. Success. I was a little concerned that the label on the back said Li-Ion, but I was again assured by the seller that the labeling hasn't been updated. Anyway, the voltages check out, so I'm happy. It charges at a 1a rate, so you're looking at 1.5 hour charge from a maximum discharge. The unit has an led that is green when fully charged or disconnected. And it shows a red led when charging.

All we're doing here is bypassing the internal charger.

The pics have descriptions. If you got past my disclaimer/warning then the pictures should show an easy modification. Feel free to post questions if something isn't clear.

CHECK, RECHECK and then CHECK AGAIN FOR CORRECT POLARITY.
And AT NO TIME CONNECT THE BATTERY DURING THIS PROCESS!!!

Good luck and...Continue Reading
Sticky: Mini Telemaster
Posted by punkindrublik | Oct 26, 2008 @ 01:29 AM | 17,595 Views
Just finished up another. Hope to maiden this week...

CCDR Cool Double
Jeti Spin 22
4 x JR SM22 servos (2 x ail)
1 x E-flite S75 (on flaps)
AR6100
Tenergy 3s 25C 850 lipos
Posted by punkindrublik | Oct 18, 2008 @ 03:39 AM | 16,883 Views
Finally getting to this little gem. It calls for a 40mm EDF, but I'm going DD.
Here it is so far...