HobbyKing.com New Products Flash Sale
BladeScraper's blog
Posted by BladeScraper | Jan 08, 2014 @ 06:31 PM | 4,202 Views
Ok, so the flight in 29 degrees went well. This thing is AMAZING.

Turning the cyclic pots down to 10 o'clock on the 3GX did the trick, no more cyclic wobbles, just crisp easy movements. This thing is SO stable!

However I do still need to sort out the tail wag, it even wags at 60% and a pitch pump really gets it wagging.

By the end of the flight my fingers were so cold I felt like I wasn't even touching the transmitter stick and it was hard to move my thumbs. I was scared to land since if I messed up and accidentally moved the cyclic stick back, the tail could hit the ground and strip a gear! I ended up just going a bit forward and landing with throttle hold on the street rather than try to land in the grass/snow-covered sidewalk.

Definitely a winner! Even with that 'crappy' Align 3GX
Posted by BladeScraper | Jan 05, 2014 @ 10:23 PM | 2,893 Views
Finally took her up while on vacation to Texas. It's a bit warmer there (65 degrees vs. 9 degrees with wind chills of less than -20 degrees...) so I figured I'd take her. The maiden was by a lake. It was a very short maiden, only a few seconds to make sure she actually flew. The real maiden was at a park. I have a video coming soon.

It flies great! There are some cyclic wobbles from high cyclic gain and a bit of tail gain, but those are issues that will be tuned out over time. The motor does get pretty darn hot, but I'm not surprised. It's not the X3's fault...

Pulse 2250 65C pack comes down cold to the touch. I'm glad. That means it won't be puffing for a while because if it does it won't fit in the heli

It's also pretty quiet in terms of drive train. However, my motor bearings suck so that alone makes it super loud. The motor is also out of balance. I will be replacing it soon.

Definitely glad I got the X3. It flies just as good as everyone said it would!
Posted by BladeScraper | Dec 26, 2013 @ 09:31 AM | 2,926 Views
Just finished her yesterday, I started building it at 9:00AM when I found it under the Christmas tree, and finished around 11:00 PM. Over 12 hours of straight building! It's sad, I know but I have nothing better to do.

I think the wiring looks great, and it better because I spent 30 minutes doing it!


Nice looking head! Much more stout than my old 450


Great tail too!
...Continue Reading
Posted by BladeScraper | Dec 25, 2013 @ 10:41 AM | 2,677 Views
Look what Santa got me!

Posted by BladeScraper | Dec 17, 2013 @ 12:46 PM | 2,441 Views
Pics of my DFC Nano


Check it out! 1mm gap from AR Guide to Grip!
...Continue Reading
Posted by BladeScraper | Dec 14, 2013 @ 11:32 PM | 3,311 Views
Man, my LHS had a REALLY big sale. I didn't know about the sale until now...

They had:

Nano = $70
mCP X = $80
mCP X BL = $90!
130X = $170

Man. I am ashamed. Lol.
Posted by BladeScraper | Nov 24, 2013 @ 09:06 PM | 2,796 Views
Almost Stock Blade mCP X V2 3D Flying in Gym (2 min 37 sec)


Very long boom, carbon skids, 42mm TR, and Xtreme 550mAh 1s 30C LiPo. Otherwise, stock. Stock motor, stock tail motor, it's great
Posted by BladeScraper | Nov 24, 2013 @ 09:05 PM | 2,634 Views
Trading my stuff for a 3Gx with 4.0 and can't wait, just need to get some digital servos...
Posted by BladeScraper | Nov 23, 2013 @ 01:21 PM | 2,345 Views
My 450 is FBL... but without a FBL unit! I haven't flown it much in this configuration yet (only skidded along the ground) but it is VERY responsive. I am looking to get an Align 3GX (cheapest yet decent enough, used) in a trade, soon, so I don't have to risk crashing due to flying NOBAR (no FBL unit)
Posted by BladeScraper | Nov 15, 2013 @ 09:22 PM | 2,365 Views
I built myself a twin tail motor setup for my mCP X. I used a 7mm and a 6mm motor because it's all I had laying around. Got it soldered up yesterday.

Went outside again for another test flight with the twin tail setup, the tail is simply rock solid! I did use a V-Curve to add pre-compensation because it would kick out a little (not blow out, just a little kick) and now with the V-Curve it's simply solid! I have always wondered what it's like to have a mCP X with a solid tail... well, now I know I can't wait until tomorrow when there's light and I can test it in 3D
Posted by BladeScraper | Nov 12, 2013 @ 08:47 PM | 2,665 Views

Green blades because they were the only pair that was balanced...


Custom tail. Soldered tail wires to a 7mm motor that came from a Xtreme Turbo Tail for Nano CPx. It was a total PITA to solder those teeny tiny wires but I got it done and it works great, especially compared to the stock tail.

...Continue Reading
Posted by BladeScraper | Nov 10, 2013 @ 02:31 PM | 2,655 Views
I am hoping for a Gaui X3 and a set of KST DS215MG servos for Christmas Only $300. I already have a motor, ESC, and tail servo, and a kit and cyclic servos are all I need for the X3. Well, and some decent batteries...
Posted by BladeScraper | Nov 07, 2013 @ 10:08 PM | 2,719 Views
Got out to the field again today just before dark. Did some 3D, not my best 3D because I'm still getting it tuned in and getting a feel for it. And it was also getting dark.

T Rex 450SE V2 Clone Second 3D Flight (crash and survived!) (5 min 15 sec)

Posted by BladeScraper | Nov 04, 2013 @ 06:38 PM | 2,364 Views
You know what I learned today?

Even the best tail setup can't counteract 20 degrees of collective pitch

Some way, somehow, the collective on my 450 got totally jacked up so that there was almost 20 degrees of positive and like 2 degrees of negative pitch... this was the cause of my tail kick. After fixing it back so that it has 10 degrees both ways, the tail is rock solid once again
Posted by BladeScraper | Nov 02, 2013 @ 12:26 PM | 3,056 Views
This servo is already insane on 5v... so what happens when you put a 2s LiPo to it? Well, you reduce transit time from 0.07s to 0.045s and increase torque from 2.5Kg to over 4Kg. The motor still stays cold to the touch!





...Continue Reading
Posted by BladeScraper | Oct 30, 2013 @ 07:49 PM | 2,790 Views
I got this

Turnigy S306G-HV. Insanely fast 0.05s, and it has 3Kg of torque! (at 6v)

Installed it on the helicopter...


And here she is ready to fly
...Continue Reading
Posted by BladeScraper | Oct 25, 2013 @ 07:07 PM | 2,808 Views
Just did a complete rebuild on my BL.

I was flying along doing some 3D and all of a sudden something off happened, the heli smashed into the ground at 1000mph. Totally destroyed... the carbon fiber frame was broken in a dozen places, boom mount got ripped completely off, tearing the carbon fiber. It was also broken in several other places.... this thing hit HARD.

I luckily had a spare frame set so I immediately got the heli apart, and then started all over again. I decided to build the frame differently than I normally would... I put everything on one half of the frame, installing every cross member, servo mount, and bearing block onto only one of the two CF side plates. I put the motor in, then put the other side plate on. I then put on the boom (actually completly remade the boom, the solid carbon rod broke the plastic tail motor holder!) on the heli. After that I installed the elevator servo, followed by the aileron servos and the 3-in-1. Plugged everything in, and it works again I took it out a few minutes ago and hovered it, it flies fine, if not better than it did before

I guess, though, this really was a kick in the butt to get me to finally sell my BL like I've been wanting to do, because if I want to sell it, I need to do so before I break it again

I don't want to sell it, but at the same time I do, so I can fund other helicopters, including the BL conversion of my mCP X, and maybe a 300X. We shall see...