Espritmodel.com Telemetry Radio
brosius85's blog
Posted by brosius85 | Sep 23, 2012 @ 08:32 PM | 2,151 Views
getting pretty close to having these ritewings dialled in perfect.

1000w D40 FPV (4 min 6 sec)


...Continue Reading
Posted by brosius85 | Aug 11, 2012 @ 06:20 PM | 2,405 Views
both new ritewings maidened successfully the demon is sooooooo much fun

the z2 flies perfect of course but the demon is just a ROCKET!

Ritewing D40 maiden (3 min 41 sec)


...Continue Reading
Posted by brosius85 | Aug 04, 2012 @ 01:43 AM | 2,356 Views
she is getting quite close to being airworthy

TBS 69 has been covered with a contoured ice cream container lid, it is rock solid and almost weatherproof

gopro door ziptied on, through the TBS battery box

this build has an extra 5mm carbon spar over the top, 5mil lam on the bottom, and 3mil on top, then vinyl covering it all up.

a few more little jobs and it maiden time!
Posted by brosius85 | Jul 08, 2012 @ 11:48 PM | 2,591 Views
i have been busy

in the next few weeks i should have my new ritewings built, a Demon 40 and a new ZII

the demon is on 2x 2s 5000 40-50c batts for 4s 5000, with a mega 16/25/2 EC from http://www.effluxrc.com/MEGA-16-25-2...16-25-2-EC.htm and an ICE 100 it will have a 6x4 APC sport prop, and also run a CC 10A BEC. video system is a 420osd cam, a HK simple osd and a LM 500mw Vtx. it will run about 1000w and should be good for 5 mins of full throttle, max speed somewhere around 120mph.

the demon build invloves....
- 2 surface wing spars
-3 centre spars, 1x 6mm FG spar buried in the centre and 2 surface spars over it top and bottom
-1 layer of riteweave and 3m90 over the whole wing
-3 more layers of riteweave + 3m90 over top and bottom from the CG forward
-gorilla glue over the whole wing, a thin layer, do not allow it to foam up. keep knocking it down for 1/2 an hour.


the ZII has ritewing motor and 80A esc, 4s 3000's x2 and also runs a CC BEC. it will have an aeronaut 10x5 folder. it will laso have Ez UHF control and an EzOSD, and a LM 500mw Vtx and a TBS 69 camera.

mods to the ZII from standard are :
-TBS battery box
-an extra 6mm carbon spar on the top inline with the 2 main buried FG spars.
-riteweave and grilla glue over the surface spars and leading edge.

more pics as the build continues.......Continue Reading
Posted by brosius85 | Jul 11, 2011 @ 07:58 AM | 4,579 Views
fpv flights:
chasing whales (2 min 26 sec)

...Continue Reading
Posted by brosius85 | Apr 28, 2011 @ 02:50 AM | 3,943 Views
righto so its time to build the zeph. have held off for a few months while learning on my IYF44 but i think im ready to build the big one.

not hard to see a big influence in this build are the TBS zephs - infact they are the reason i ever got into rc. after seeing the footage uncle trap gets i knew this was the sport for me.

so yeah im building it the RITE way unlike the ultralite way everyone seems to be for fpv but i built my IYF44 ultralight and have since broken one of the wing spars pulling high g's in a loop so i want this to be BULLETPROOF. 3M90 and riteweave allround!

seriously noone stocks the glues i need for this build so i just bit the bullet and went to amazon...... D: $30 for some white gorilla and 3M tape hmmm...

anyway i cant glue the wing spars in till i get the gorilla glue and i cant cut the bays out till i get the bottom layer covered in gorilla and weave. so here is the progress so far.
Posted by brosius85 | Jan 04, 2011 @ 12:13 AM | 4,039 Views
i just got my microdan 2505 1845kv motor in the mail so

straight to the shed to make the motor mount

took a few snaps as i was going

here they are