SMALL - espritmodel.com SMALL - Telemetry SMALL - Radio
myrcmart's blog
Archive for July, 2011
Posted by myrcmart | Jul 26, 2011 @ 11:36 AM | 7,866 Views


Special for USD6.99 only.

Specification

* Model: RCX BC1712-15
* Motor size: Ф22*25mm
* Shaft size: Ф3.175*41mm
* Weight: 32g
* KV(rpm/v): 1600
* Max Power: 90W
* Battery: 2-3Li-Po
* Test Prop: 8x4/7x3
* Ri(M Ω): 0.203
* ESC(A): 18A

http://www.myrcmart.com/rcx-bc222515...or-p-3717.html

Package Included

* 1 X RCX BC1712-15 1600KV Outrunner Brushless Motor
* 1 Set of Screw
Posted by myrcmart | Jul 18, 2011 @ 03:37 PM | 7,380 Views
RCX S9257 is a high speed, high torque digital servo suitable for 450 & 500 series helicopters. It is an excellent tail locking servo for 3D flight.

http://www.myrcmart.com/rcx-s9257-hi...le-p-3600.html

Equipped with two ball bearings.

For use with the Futaba GY401 (FUTM0807, FUTM0808) and the GY502 gyros.

Does not work with these Futaba radios (4FG, 5FG/K, 6FG, 6FG/K, 7FG/K New Terratop, 3EGX, 3PGE, 2NL, 2LGX, 2FR, 2PK series) These radios have a servo neutral signal of 1310us not compatible with this servo.

Do not use with AM radios.

Specification

* Dead band: 0.002ms (Default)
* Control System: +Pulse Width Control
* Working Frequence: 1520μs / 80hz Digital mode/Analogy mode
* (RX) Required Pulse: 3.0~5.0 Volt Peak to Peak Square Wave
* Operating Voltage: 4.8~6.0 Volts DC
* Operating Temperature Range: -10 to + 60 Degree C
* Operating Speed (4.8V): 0.08 sec/60 degrees at no load
* Operating Speed (6.0V): 0.07 sec/60 degrees at no load
* Stall Torque (4.8V): 3.8 kg.cm
* Stall Torque (6.0V): 4.2 kg.cm
* 360 Modifiable: NO
* Motor Type: Coreless Motor
* Potentiometer Drive: Indirect Drive
* Driver Type: FET
* Bearing Type: Dual Ball Bearings
* Gear Type: Plastic Gear
* Programmable: YES
* Connector Wire Length: 18.0
* Dimensions: 35.5mm x 15.0 x 28.6mm
* Weight: 25 g


Package Included

* 1 X RCX S9257 High Speed Digital Servo (4.5kg / 25g / 0.07sec / Tail & Rudder Servo Suitable)
* 1 X Set of Servo Arm
Posted by myrcmart | Jul 10, 2011 @ 03:44 AM | 8,131 Views
RCX MG9257 is a high speed, high torque digital servo built with Metal Gear suitable for 450 & 500 series helicopters. It is an excellent tail locking servo for 3D flight. It could also be used as a Swashplate Servo for larger helicopters (eg. 500 / 600 size helicopters)

http://www.myrcmart.com/rcx-mg9257-h...le-p-3716.html

Equipped with two ball bearings.

For use with the Futaba GY401 (FUTM0807, FUTM0808) and the GY502 gyros.

Does not work with these Futaba radios (4FG, 5FG/K, 6FG, 6FG/K, 7FG/K New Terratop, 3EGX, 3PGE, 2NL, 2LGX, 2FR, 2PK series) These radios have a servo neutral signal of 1310us not compatible with this servo.

Do not use with AM radios.

Specification

* Dead band: 0.002ms (Default)
* Control System: +Pulse Width Control
* Working Frequence: 1520μs / 80hz Digital mode/Analogy mode
* (RX) Required Pulse: 3.0~5.0 Volt Peak to Peak Square Wave
* Operating Voltage: 4.8~6.0 Volts DC
* Operating Temperature Range: -10 to + 60 Degree C
* Operating Speed (4.8V): 0.08 sec/60 degrees at no load
* Operating Speed (6.0V): 0.07 sec/60 degrees at no load
* Stall Torque (4.8V): 3.8 kg.cm
* Stall Torque (6.0V): 4.2 kg.cm
* 360 Modifiable: NO
* Motor Type: Coreless Motor
* Potentiometer Drive: Indirect Drive
* Driver Type: FET
* Bearing Type: Dual Ball Bearings
* Gear Type: Plastic Gear
* Programmable: YES
* Connector Wire Length: 18.0
* Dimensions: 35.5mm x 15.0 x 28.6mm
* Weight: ~30g


Package Included

* 1 X RCX MG9257 High Speed Digital Servo (4.5kg / 25g / 0.07sec / Metal Gear / Tail & Rudder Servo Suitable)
* 1 X Set of Servo Arm