HobbyKing.com New Products Flash Sale
rc-fans88's blog
Posted by rc-fans88 | Aug 20, 2012 @ 08:10 PM | 3,423 Views
HL W42-25 390KV Outrunner Brushless Disk Type Motor for 450-650 Multi-copter


Features
-HL disk type motors specially designed for multi-rotor aircrafts.
-Utilizing 0.2mm Silicon steel sheets.
-Well balanced at factory, ensures maximum efficiency and low noise.
-Higher g/w ratio, very good choice for muti-rotor application.
-New motor mount suits for different mounting spaces.
-New prop adaptor design, you can fix the prop with prop adaptor, or mount the new series carbon fiber props directly to the motor without using prop adaptor.

Product Details
-Model: W42-25 390KV
-Idel current: 0.2A at 7.4V
-Net weight: 87g
-Max cell number supported: 6S Lipo
-Max current: 15A
-Recommended ESC: 20A
-Working current: <11A
-Max power: 330W
-Internal resistance: 0.24Ω

Item Packing
-Motor X 1
-Prop adaptor X 1
-Prop adaptor screws X 4
Posted by rc-fans88 | Aug 09, 2012 @ 10:32 PM | 3,329 Views
DJI Naza Flight Stabilization Controller ( Multicopter ) DJI-NAZA
Part No : DJI-NAZA

Features
All-in-One Design integrates inner damping, controller, gyroscope, accelerometer and barometer, which simplifies installation and saves space.
Advanced mix guidance algorithm and control algorithm, inherits outstanding flight stability of DJI products, provides excellent maneuverability, gives hobbyists wonderful flight experience
Two-level low voltage protection. low voltage LED alarm, and automatic landing.
D-Bus supports S-BUS receiver system
The gimbal stabilization module is compatible with almost all 2-axis gimbal systems. The system will adjust the gimbal and camera according to the attitude of the helicopter after setting the parameters the first time.
Upgradeable and extendibleEasy firmware upgrade, extendible port for future use is available.

Product Details
Built-In Functions Autopilot
Auto Level Fail-safe
Low Voltage Protection
S-Bus Receiver Support
2-axle Gimbal Support
Peripheral
Supported Multi-rotor Quad-rotor I, X;
Hex-rotor I, V.
Supported ESC output 400Hz refresh frequency.
Recommended Transmitter PCM or 2.4GHz with minimum 4 channels.
Assistant Software System Requirement


Item Packing
DJI NAZA Multirotor Stabilization Controller by DJI Innovations for Quadcopters x 1

English Manual x 1
Posted by rc-fans88 | Aug 09, 2012 @ 04:57 AM | 3,795 Views
Rabbit GPS Receiver w/ u-blox GPS module for Rabbit Flight Controller Multi-Copter MultiCopter Part No : YTK-A8
Features

Rabbit GPS adopts ublox brand GPS module which was regarded as the best for the performance.High accuracy, low drifting, stable and high price ratio

- Rabbit GPS needs a very stable and reliable aircraft debugged.
- GPS ceramic antenna faces up, GPS and Rabbit Flight Controller should keep a distance of more than 10cm.
- The rabbit GPS is connected to the flight controller pinout with 4Pin Dupont line.
- The normal work of Rabbit GPS needs the cooperation of self stability mode, height lock, magnetic sensor.
- Operate for Rabbit Flight Controller and Rabbit Flight Controller with Fixed Hight Direction Care Free.
- The rabbit flight controller can fit for the GPS module now,and we also provide the firmware for the old rabbit FC users.

Product Details
- Demensions: 40 x 26 x 12mm (L x W x H)
- Weight: 18gram only


Item Packing
-Rabbit GPS Receiver w/ u-blox GPS module for Rabbit Flight Controller Multi-Copter MultiCopter x 1
Posted by rc-fans88 | Aug 08, 2012 @ 08:52 PM | 3,526 Views
Skywing 48-Inch EPP SBach 342 Kit Blue

Features
-This 48-in SBach 342 is based on the success of Skywing's 48-in YAK 54 and 42-in SBach 342. It has a two-piece detachable wing for easy transportation and storage, and a detachable canopy piece for easy battery and receiver access.


Product Details
- Wingspan 1235 mm (48.6 inch)
- Length 1095 mm (43.1 inch)
- Flying Weight 980-1050 g (34.6-37.0 oz)
- Manual (in Chinese only)

Requires:
- Propeller 12x6, 13x6.5
- Motor: FC3542 950Kv Outrunner
- ESC: 40A
- Servo: 14g x 4
- Battery: 11.1V 1800-2200 mAh 20C Lipo



Item Packing
-Skywing 49-Inch EPP SBach 342 Kit BLUE
Posted by rc-fans88 | Sep 28, 2011 @ 09:30 PM | 5,308 Views
FEIYU Inertial Attitude Stabilizer FY-30A
FeaturesFY-30A is an inertial attitude measurement instrument used for automated stabilization of fixed
wing model aircrafts and two axis camera gimbals.
FY30A has an integrated three-axis gyro and three-axis accelerometer which controls the aircraft
movement in three-dimensional space. By using your remote control, the unit can be turned on or
off for the following functions:
● Level flight – When stabilizer is activated, the FY-30A will automatically control the
aircraft for smooth easy flying. For beginners in RC aircraft flying, this is advantages as
it makes flight easier and increases the student pilot self-confidence. The system can be
activated throughout the entire flight duration, from take off to landing.
● Emergency Recovery - If you lose orientation or feel the plane out of control, then
release all control sticks, maintain throttle and switch on the FY30A. The unit will
automatically send the correct signals to balance of the aircraft and regain level flight.
● Aerobatics – for the experienced fixed wing 3D pilot, the FY-30A can help you achieve
a more accurate flight path, especially in windy conditions. FY-30A makes 3D
maneuvers such as inverted flight, , crane etc easier and simpler to achieve and maintain.
A great way to practice and improve your 3D flying.
● First Person View - for long-distance RC flight via video transmitter, the FY30A will
maintain the balance of your...Continue Reading
Posted by rc-fans88 | Sep 15, 2011 @ 03:54 AM | 5,287 Views
RC Model Metal Servo Arms 25T For Futaba
Part No.: SO004

Features
-RC Model Metal Servo Arms 25T for towerpro mg995, Futaba, Fitec Sevrvo
Product Details
-Material: Metal CNC
-Teeth:25T

Item Packing
-RC Model Metal Servo Arms
Posted by rc-fans88 | Aug 25, 2011 @ 02:56 AM | 6,592 Views
Skywing 48-Inch EPP SBach 342 Kit
Part No.: EP004

Features
-This 48-in SBach 342 is based on the success of Skywing's 48-in YAK 54 and 42-in SBach 342. It has a two-piece detachable wing for easy transportation and storage, and a detachable canopy piece for easy battery and receiver access.
Product Details

- Wingspan 1235 mm (48.6 inch)
- Length 1095 mm (43.1 inch)
- Flying Weight 980-1050 g (34.6-37.0 oz)
- Manual (in Chinese only)

Requires:
- Propeller 12x6, 13x6.5
- Motor: FC3542 950Kv Outrunner
- ESC: 40A
- Servo: 14g x 4
- Battery: 11.1V 1800-2200 mAh 20C Lipo
Item Packing

-Skywing 49-Inch EPP SBach 342 Kit

Note: 5pcs/ Carton

Flight Video: Please copy the following address to view:

http://v.youku.com/v_show/id_XMjQwMDY2NzUy.html
Posted by rc-fans88 | Aug 23, 2011 @ 09:01 PM | 6,159 Views
Upgrade CNC Metal Rotor Head Nine eagles 260A Solo PRO
Part No.: AP010

Features

-New Nine Eagles 260A Solo pro SOAR CNC Metal Rotor Head

Product Details

-Material:CNC Metal
-Color:Silver
-Compatible with: Nine Eagles 260A

Item Packing

-New Nine Eagles 260A Solo pro SOAR CNC Metal Rotor Head
Posted by rc-fans88 | Aug 04, 2011 @ 08:58 PM | 5,415 Views
Fitec Standard 12kg.cm Digital metal gears servo
Part No.: FS5513M

Features
-Standard digital Titanium gears servo、2BB
-Coreless motor、Aluminium middle hull
-Waterproof
-Operating Voltage: 4.8V~7.4V
-Dead band width: 2usc
-Interface: (like JR)
-Wire length: 30cm

Product Details

Power:4.8V-6V
Speed:0.14sec/60° 0.12sec/60°
Torque:10.5kg.cm/146.7 oz.in 12.5kg.cm/173.6 oz.in
Weight:56g (1.46oz)
Size:40.2*20.0*38.6mm
Application:Air plane、Car、boat

Item Packing

-Servo×1PCS
-Servo arm×1 bag
-Carton box
-GW: 90g
Posted by rc-fans88 | Aug 03, 2011 @ 04:22 AM | 6,669 Views
eFUEL 110V Input 9-18V 30A 540 Watt Output Switching AC/DC Power Adapter

Part No.: LC-Imax30A-ADU

Features
-Your eFUEL switching DC Power Supply is designed to use household AC power source to power
equipments that required DC power. The eFUEL converts standard household power 110-120V AC
or 200-240V AC to 9-18V DC power and can supply up to 30 amperes of continuous power.
If you are R/C hobbyist, technician or electronic hobbyist, you will appreciate the many uses for the power supply at your workbench or in your house. For example, power your battery chargers, checking the operation of auto sound systems before you install them into your vehicle, use your CB mobile transceiver as a base station. To top it all off, you can even power your mobile phone, digital camera or even your iPhone via the USB port.

Product Details

-Voltage:110V AC (Part No.PSU30ADU,PSU30AU)
-220V AC (Part No.PSU30ADE,PSU30AE)
-Input AC Frequency:50Hz/60Hz
-Output Voltage:9-18V DC±0.5V
-Output Curren:30A±1A
-Current Overload Protection≤31A 500MS
-Input Fuse:110V AC 10A Fuse
-220V AC 5A Fuse
-LCD Display:Voltage Precision ±0.3V
-Current Precision ±0.5A
-Output Voltage Ripple:<100MV
-Power Efficiency>80%
-Power Factor>0.7
-Over Temperature Protection<100℃
-Cooling Method:Cooling Fan
-Operating Temperature:0-40℃
-Operating Humidity:0-90%
-Dimensions (L*W*H):208x139x59.5mm
-Net weight:1.50kg

Item Packing

-eFUEL 110V Input 9-18V 30A 540 Watt Output Switching AC/DC Power Adapter
Posted by rc-fans88 | Jul 28, 2011 @ 10:17 PM | 6,763 Views
JC23 EVO 23CC 2-Stroke Gas/Petrol Engine
Part No.: JC23

Features

- 2 Stroke air cooled single cylinder
- Walbro membrane pump carburetor with dual needles and manual choke
- Automatic advancing electronic ignition

Product Details

-Engine type :2—Stroke gasoline engine
-Displacement:23cc
-Bore × Stroke: 33.3mm × 27mm
-park plug: NGK CM6 or JC CM6
-Carburetor: Walbro special-designing vacuum pump diaphragm type duplex needle carburetor
-Max power :3.5hp/9500rpm
-Practical running speed : 1100 - 9500rpm
-Net Weight :980g (incoulding CDI and muffler)
-Ignition system :CDI battery ignition (battery voltage: 4.8v—6v)
-Grease oil ratio :25-30:1 used during the break-in (the initial 2 working hours); 35-40:1 used after the break-in.
-Screw propeller dimension : 16x8, 16x10, 17x8, 17x10, 18x8

Item Packing

-JC23 EVO 23CC 2-Stroke Gas/Petrol Engine
Posted by rc-fans88 | Jul 26, 2011 @ 09:05 PM | 5,378 Views
FEIYU GPS & Compass Module for Multi Rotor System
Part No.: FYGPSC

Features-THIS IS THE GPS & COMPASS MODULE MENTIONED
Product Details-GPS & COMPASS INTERFACE MODULE
-Operating voltage :4.0~6.0 Volt
-Current consumption : 60mA (5V input)
-Dimensions :55 x 33 x 20 mm
-Weight (not including wire) :20g
-Temperature range :-25°C~ +70°C
Item PackingFY-91Q control module x 1;
-GPS & COMPASS Interface module x 1;
-FY GPS Receiver x 1
-Related wiring to complete the set up
Posted by rc-fans88 | Jul 14, 2011 @ 10:12 PM | 5,821 Views
WM EPP series electric model airplane
Part No.: EP-WM KIT

Features

-The product is mainly made of EPP material, light-weight and resistant. Due to this special material, serious demage would not be caused by slight faulty operation.
-The revolutionary design adds to the structural intensity and the rigidity of the airframe which is even made of EPP material, while ensuring the flight more stable and easier controlled.
-Light-weight design provides optimal Wing loading while ensuring the permanently strength of the craft. This characteristic contributes to the perfect flying performance.
-The composition and the proportion are well matched to provide excellent flying characteristics, while still allowing for precision aerobatic performance and 3D maneuverability.
-Simple design allows for easy access and installation. And all necessary accessories are provided in the package.
-The color schemes are painted with new oil paint which makes the color fresher and permanent.
- Its small size excels at flying on a limited open space, such as park. It also fits into a very small car for transport.

Product Details

-Wing span:955MM
-Length:945MM
-Wing area:15.2dm2
-Weight:480g (without battery)
-Requirements:
-Motor: 2834;2212;2217;950-1100KV Brushless outrunner
-ESC: 25-30A
-Battery: 3S 11.1V 1000-1300MAH Li-po
-Prop: 1047/1147
-Servo: 1.5-2kg/cm;0.1-0.18sec;(4pcs)

Item Packing

-WM EPP series electric model airplane KIT X 1
Posted by rc-fans88 | Jul 10, 2011 @ 09:22 PM | 5,664 Views
38(D)x40(H)mm /1.5 inch Plastic Spinners -Red
Part No.: SP-P002


Features
-38(D)x40(H)mm /1.5 inch Plastic Spinners -Red

Product Details
-Plastic Spinner for 2-blade prop
-Size: Φ38x 40(H) mm
-Weight: 11g

Item Packing-Plastic spinner X 1
-Screws X 2
Posted by rc-fans88 | Jul 07, 2011 @ 10:11 PM | 5,897 Views
FPV-specific entry-level aerial camera DV-One Printer / built-in 2GB memory card
Part No.: CA-008

Features
-The most easy to use entry-level aerial integrated mini-recorder with super mini form factor and light weight (host only 20g) ,1-4GB built-in memory, plug and play USB connection.
-Suitable for any model of helicopter and fixed-wing aircraft installation
-Illumination, 2 million high-definition camera;
-High-speed dynamic video, light and dark environments transient response;
-Video output: 640 × 480px 30 frames / sec;
-Built-in lithium battery for 2 hours continuous use
-Fool-operation, integration of lighting control indicator, automatic shut down;
-Mini USB to computer and video upload download transfer function


Product Details
-Product Name: FPV-specific entry-level aerial DV camera-one / built-in 2GB memory card
-Manufacturers No.: FPV-DV
-2000000 pixels CMOS
-62 degrees viewing angle
-Minimum illumination 1Lux
-Battery capacity 260mAH
-Power 130mA/3.7V
-Storage temperature -20 ℃ ~ 80 ℃
-Operating temperature -10 ℃ ~ 50 ℃
-Operating Humidity 15-85% RH
-Capacity built-in 2G
-Video codec using the video features Motion JPEG, MP4 file format into recorded
-USB interface USB1.1
-Weight 20g (approx.)
-Operating System Windows 98SE/2000/Me/XP/Vista

Item Packing-FPV-specific entry-level aerial camera DV-One Printer / built-in 2GB memory card
Posted by rc-fans88 | Jul 06, 2011 @ 09:18 PM | 6,272 Views
Fitec Standard 21.0 kg.cm HV Digital metal gears servo FS5621M

Features

-Standard digital Titanium gears servo、2BB
-Coreless motor、Aluminium middle hull
-Waterproof
-Operating Voltage: 2-cell Li-Po power
-Dead band width: 2usc
-Interface: (like JR)
-Wire length: 30cm

Product Details

Power:7.4V-8.4V
Speed:0.16sec/60° 0.14sec/60°
Torque:17.8kg.cm/247.2 oz.in 21.0kg.cm/291.7 oz.in
Weight:56g(1.41oz)
Size:40.2*20.0*38.6mm
Application:Air plane、Car、boat

Item Packing


-Servo×1PCS
-Servo arm×1 bag
-Carton box
-GW: 90g
Posted by rc-fans88 | Jun 22, 2011 @ 09:35 PM | 6,007 Views
Wing Tote/ Wing Bag/ wing protector for 50CC gasoline engine M Size

Features
-Protect your valuable wing panels!
-Keep it clean and organized!
-Easy to carry in the car or out to the field!

Product Details
-It’s made from the highest quality durable, water resistant nylon material;
-External material has Sun reflective characteristics to protect your wings from absorbing outdoor heat
-Foam padded divider in the middle totally separates the two wings,
-It’s foam padded between outer and inner material protect your wings while in transportation and storage
-extra safety straps at the entrance provide double security and also allows for larger wings
-The smooth inside material provides friction protection of the wing covering
-A large compartment on both sides for the stabs, props and other accessories,
-It has an individual wing tube pocket, for easy insertion with Velcro secured entrance;
-Adjustable length of Shoulder strap
-Comfortable Shoulder webbing to evenly distribute the weight on your shoulder
-Transparent PVC name tag side pocket
-YKK zips ensure the highest quality and long life
Item Packing-wing-bag size for 33~35% airplane

Posted by rc-fans88 | Jun 20, 2011 @ 04:03 AM | 7,879 Views
NEW JC-30 EVO 30CC 2 Stroke Gas Engine for Gas Airplane.
Quality very good, as good as DLE.

Features

-2 Stroke air cooled single cylinder
-Walbro membrane pump carburetor with dual needles and manual choke
-Automatic advancing electronic ignition

Product Details

-Engine type : 2—Stroke gasoline engine
-Displacement:30cc
-Bore × Stroke: 36mm × 30mm
-park plug: NGK CM6 or JC CM6
-Carburetor: Walbro special-designing vacuum pump diaphragm type duplex needle carburetor
-Max power : 4.0hp/9000rpm
-Practical running speed : 1100 - 9000rpm
-Net Weight : 1100g (incoulding CDI and muffler)
-Ignition system : CDI battery ignition (battery voltage: 4.8v—6v)
-Grease oil ratio : 25-30:1 used during the break-in (the initial 2 working hours); 35-40:1 used after the break-in.
-Screw propeller dimension : 18*8, 18*10, 19*8, 19*10

Item Packing
-JC30 EVO 30CC 2-Stroke Gas/Petrol Engine
Posted by rc-fans88 | Apr 23, 2011 @ 01:29 AM | 5,927 Views
LOTUSRC Quadcopter --AP/AV based ARTF (FPV Carrier)LRT580

Features
-Inertial-based(6DOF IMU) self-stabilization system.Good for AV/AP applications,but not suitable for acrobatics flights.
-4 channels Tx is enough.No more switchs for the flight modes
-ARTF,no extra settings needed.Put on the props,the battery and the RX,then turn on the Tx to take off !
-AP/AV based
-Auto Barometer-based altitude hold if no throttle input changed in 2s..
-X and Corss flight modes available.Only Cross mode was available in the beginning.But new improvements for the X mode had been tested successfully.
-Optional single axis camera mount(pitch) with double axis self-stabilization(pitch and roll).
-Larger MTM distance(580mm),larger payload (<580g),and longer flight time(25 mins with 3S Battery).Special props offered by the manufacture.
Powerful
-Optional GPS position hold(The GPS module still in internal testing, not included in this kit).
-Buzzer warning for low battery,and optional lights for night flight(The interfaces are available,but soldering should be done before coming out -of the factory according to the demands of the costomers.In order to avoid some trouble of making the hardware easy to be damaged).
-Other features considering to be supported in the future:Configuration Software available and Firmware upgradable.
-This is the ARTF kit, basically speaking, you only need a receiver and transmitter to get it ready for flying.
Product Details
Machine size

608...Continue Reading
Posted by rc-fans88 | Aug 25, 2010 @ 10:06 PM | 8,058 Views
3 Ch Syma S006 Alloy Shark RC l Metal Frame Helicopter with Gyro
Features
Function: Up/Down, Left/Right, Forward/Backward
Product is 100% new, never used

FULLY ASSEMBLED, READY TO FLY

Product Details
Flight Time: 8-9 minutes
Controller Type: A pole square

Battery for controller: load 8"AA" batteries

Battery: Li-Poly 3.7v 1000mAh

Metal Frame

Product size: 37.5*14*17.5 cm

Box size: 63*23*11 (cm)

Charge time: about 1 hours

Aviate Time: 8-9 minutes

Aviate Height: 20-30m

Aviate Area: 20-30m

Item Packing
1 x Helicopter
1 x Remote Controller

1 x Spare tail propeller

1 x Instruction Manual

1 x Charger

1 x Sscrewdriver