Le Fish
Slope plane
Simple combat wing
Current gear;
ARC 110 with GWS 6x3 cut to 5x3
TP910 2s or any 40-45g
5-9g servos
This wing in action but with blue foam.
Little bit of everything blue combat, Don flying the wing and filming.
http://www.rcgroups.com/forums/showthread.php?t=907060
Fun in the yard, down in Fla.
http://vids.myspace.com/index.cfm?fu...deoID=51876170
More at the field shot by Alexander, 8 at the time.
http://vids.myspace.com/index.cfm?fu...deoID=47496590
Basic cut out here, just and mid mounted motor.
http://www.rcgroups.com/forums/showp...&postcount=135...Continue Reading
ARC 110 with GWS 6x3 cut to 5x3
TP910 2s or any 40-45g
5-9g servos
This wing in action but with blue foam.
Little bit of everything blue combat, Don flying the wing and filming.
http://www.rcgroups.com/forums/showthread.php?t=907060
Fun in the yard, down in Fla.
http://vids.myspace.com/index.cfm?fu...deoID=51876170
More at the field shot by Alexander, 8 at the time.
http://vids.myspace.com/index.cfm?fu...deoID=47496590
Basic cut out here, just and mid mounted motor.
http://www.rcgroups.com/forums/showp...&postcount=135...Continue Reading
EZ Spin V2.0
Cable driven vectored thrust layout....Continue Reading
Finished and waiting test flights
Ready
At Brad's shop getting the goodies together
Late updates
Ready for ARC 28-47-1.5
Few more shots with motor mount hard points in place.
Back to the E Wizz
I guess Brad liked the colors of the Glow pwr Wizz so its a repeat.
They do stand out in the air and contraz well.
Its covered, hinged and servo'ed.
Need motor mount hard points, bottom fin, linkages and horns but it's a long weekend
They do stand out in the air and contraz well.
Its covered, hinged and servo'ed.
Need motor mount hard points, bottom fin, linkages and horns but it's a long weekend
Another Delta to be E'ed
Diamond Dust is next on the block.
Drive depends on how E Wizz works out
Drive depends on how E Wizz works out
Build done
Cover and gear next
Option 6
MiniBox/ARC 28-47-1.5 will be the most likely path.
Pictured motor is for form and fit only.
Pictured motor is for form and fit only.
-
Views: 303
Less the Glow Motor, this is typical of the end product. (Its actually the last one I built in FL) -
Views: 211
(Initial mock up) Mounting plate will be either Aluminum or Carbon Fiber. Oversized at this point, it will be thinned down once all mounting points are set as well as positioned flush with the mounting plate lead edge.
Few other GB options to look at.
Astro,Mega and Maxon
What next, 28mm motor w/GB or NO Don’t say it, Outrunner
Typ MEC gb layout
-
Views: 313
Compare adaptors and motor shafts on MEC GB. MR 28mm with MEC adaptor (blue), Neu 1107 and AstroFlight adaptor (Aluminum) -
Views: 194
Checking depth of GB and motor (actually could run this way) -
Views: 212
Another mounting option, motor plate would be notched and assembly set back from this position with prop shaft flush with front of the plate. -
Views: 226
Picture this set-up only inset back approx. 20-25mm -
Views: 188
As far as the mounting goes, its a blank canvas. Outrunner mounting with cut-a-way the most all the plate that ties the LE and Spars into the airframe, but that will be overcome it needed. -
Views: 197
Shaped and ready for flying surfaces and covering, as it sits, 6.2oz/177g
E Wizz ready for fitting motor
Brads turn
More E Wizz
Forming the ribs over the spars
40 Wild Wizz Build
E conversion for Brad S.
