SCREWS First Flights Diode Voltage Drop - To lower voltage of a supply source
Changing to new version swashplates and carbon main shafts should have added some screws. On the ones with Delrin main gears, you can grab extra screws from the ring collars as the thicker Delrin main gears should allow the main shaft to drop without disengaging the pinion.
Then you have gobs of extra screw that can be robbed from the dual-charger and transmitter.
Reminds me, when putting screws back into plastic, turn the screw backwards (out) until you hear a click as the screw finds the original threads, then turn the screw in. Avoids stripping the plastic threads.
If you have problems getting into the air, try getting the helicopter quickly to eye level to get out of the ground effect, or hand launch if all else fails. You may find a slow lift-off causes the helicopter to scoot left, so be prepared for it. A slow lift-off can be done smoothly after you learn to control the helicopter.
A good launch pad is a (soft) cardboard box about 2 feet high. Then fly forward off the edge into clean air. The helicopter will drop but you already are adding throttle so just keep adding more.
All my V911's will violently scoot left (viewed from tail) on take off. I think it is the tail rotor pushing it left. When in the air, there is a right tilt on hover which means the left drift is being corrected by right aileron. That is the way they hover, even after setup...Continue Reading
Many flyers wind-surf with V911's because you can try anything with a V911, not fearing a damaging crash - worst case, $20 V911 BNF, just buy another one and use the old one for parts. If you are afraid to crash, then don't wind-surf.
Start by not using ailerons. Rudder is much quicker.
Apply full forward trim to keep the nose from coming up too high, and fly low, to avoid letting the wind get it.
Practice hovering nose into the wind . Push the nose down and apply throttle to hold position or to move forward.
To gain forward speed when nothing else works, turn to the side and fly a crosswind zigzag pattern.
Practice nose-left (counter-clockwise) circles to fly around and nose dive into the wind again. Ease up on the nose and bank one way or the other into the oncoming wind. Nose-right circles may be faster but harder to control (recover) after you get downwind.
Lots of practice. In calm or little wind, practice nose-left circles: Nose down to get forward motion, then full left aileron followed by small amount of left rudder, then aileron neutral, gets smooth banked wide circles. Use rudder to control diameter and throttle to maintain altitude, or allow the helicopter to dive close to the ground under the wind.
Forgot to mention that you always keep moving, crosswind zigzag, or circling back. Zigzag picks up speed when you turn. Circling back picks up speed downwind after turning into the wind and diving into the wind head-on. The fun part is at...Continue Reading
Posted by Ribble |
Aug 16, 2012 @ 03:02 AM | 4,723 Views
V911 Binding Newer Version V911 Transmitter Origami 2k-2k-1k Transmitter Rudder Modification - Reduces Rudder Throw Vibrations Gradual Rotation Binding Yellow V911 Helicopter V911 Stock Batteries USB Hub Charging Batteries Transmitters That Bind And Fly V911 Helicopter V911 Wind-Surfing
Transmitter off, throttle minimum
Transmitter on quickly while V911 LED is blinking fast
You may have to turn the transmitter OFF and ON after V911 LED blinks slow again
V911 LED is on solid after good binding.
Newer Version V911 Transmitter
The original V911 transmitters moved the rudder so much that the helicopter was hard to control. The newer version reduced how much the rudder stick causes the helicopter to rotate and makes flying the V911 much easier. In low rates, the newer version transmitter shows two tabs on the LCD display for full left or full right rudder.
Night flying and reduced current draw. Numerous measurements http://www.rcgroups.com/forums/showt...s#post22546678
The two 2k resistors add exponential at rudder mid-stick, balancing rudder to neutral. The 1k resistor selects how much the stick potentiometer unbalances the two 2k resistors and reduces overall rudder control.
Short the 1k resistor to regain full rudder throw with exponential at mid-stick (works only on old V911 stock...Continue Reading
Posted by Ribble |
Aug 16, 2012 @ 01:57 AM | 3,605 Views
Transmitters That Bind And Fly V911 Helicopter V911 Wind-Surfing Motor Overheating Gyro Test Spins nose-right (clockwise) problem Rudder Fake-out Mixing Arms Reversed Troubleshooting And Other Information Stuck Servo Servo Repairs V911 Helicopter Printed Circuit Board (PCB)
Transmitters That Bind And Fly V911 Helicopter
Stock V911 transmitter (and V929 quad transmitter), still best bang for bucks.
Turnigy 9x and clones
FS-CT6B - What I use when wind is steady, allows hands off hover pointing into wind.
Unconfirmed report that Trex 100 is "fully compatible"
In my opinion, the best for price, performance, ease of use, is the stock V911 transmitter. But then I only fly V911's in low rates windsurfing outside, Elevator trim full forward.
For forward flight with the V911, push the nose down and add throttle. Throttle makes it go faster as well as maintaining altitude.
When playing in the wind, keep the nose down or the V911 will float away in the wind. Control forward speed with throttle. Practice nose-left (counter-clockwise) turns to circle around and dive back into the wind. Nose-right turns are easy but hard to pull out of because the V911 picks up too much speed.
To check for motors overheating, touch the main motor and kiss the tail motor. Touching tail motor to your nose also works quite well, but my nose isn't calibrated for heat. After you kiss the tail motor, get in the habit of blowing air into...Continue Reading
Posted by Ribble |
Aug 07, 2012 @ 01:20 PM | 3,332 Views
Solder bridge the Motor Overload Protection System (MOPS). Suggest scraping some green enamel and splash solder across, right below the two MOPS leads (white line between leads). This grounds the source leads on the two motor FETs (like on the DH9104) Do not remove the MOPS orange loop.
You can put a wire jumper across the MOPS connections, but you stand a chance of ruining those connections, which are critical. So create a solder bridge below the connections. The solder bridge will have some resistance and there will remain some minor motor protection. To later undo the solder bridge, move the soldering iron down the gap between the enameled copper.
MOPS leads - Scrape green enamel below and solder bridge
>I've put on a solder bridge and that solved the problem. I can now spool up to full power without any cut-out affect.
>It was recommended only to do this with the stock battery - my plan is to use a 900mah 20C (40C burst) battery.
Adding more battery mah with a battery that weighs the same as the stock battery does not add any additional workload. A higher "C" rating allows you to fly harder, though the average workload will still be about the same - unless you use the additional available power to fly straight up for a long time, or stall a motor by not turning throttle off upon crashing..
Adding more battery mah with a battery that weighs the same as the stock battery does allow flying longer with added...Continue Reading
Posted by Ribble |
Aug 07, 2012 @ 01:16 PM | 2,746 Views
The servos run off the +5v voltage regulator. You can short circuit the voltage regulator and it will just limit the current and work fine when the fault is cleared. Shorting the voltage regulator would drop the gate voltage on the motor switching FETs and turn them off, stopping the motors.
The servos have +5 volts on the center pin (of three) and you can plug the servo connector in backwards with no damage, the servo just won't work. Someone a while back was using a jumper wire to short the servo connector and all it did was reset the DH9116 receiver.
Sounds unlikely that a bad servo could cause damage to anything else.
What will kill the circuit board is stalling a motor. Kill the throttle before you crash. Stalled motors will suck up all the amperes that the LiPo or Li-Ion battery can provide and with a good battery, something has to burn out. It can happen faster than the Motor Overload Protection System (MOPS) can act.
DH9116 printed circuit boards are quite rugged and take much abuse.
Posted by Ribble |
Aug 07, 2012 @ 01:11 PM | 2,714 Views
Yes, MOSFET - Metal Oxide Semiconductor Field Effect Transistor.
In the beginner section, one should not abbreviate. Spelling out what MOSFET stands for only makes it worse.
In the case of the DH9116, they are power transistors that are controlled by an electrical charge on the "gate". Put zero volts (ground) on the gate and the transistor turns off (turns very off, like it isn't there). Put +5 volts on the gate and the transistor turns on (turns very on, like a direct short). The gate only needs a voltage and no current, so the power needed to control the MOSFET is practically zero watts.
Fantastic devices. The two MOSFETs on the DH9116 printed circuit board can switch (I seem to recall) 80 amperes to turn the main and tail motors on and off.
A short circuit dissipates no power. An open circuit dissipates no power. The MOSFETs only dissipate power during switching, the transition between a short and an open.
But voltage spikes from the motor's inductance during switching will kill a MOSFET. So, across the main and tail motor connectors are "snub" diodes to short motor spikes.
Enough electronics. MOSFETs are such a mystery to RC helicopter pilots, but are as vital as the LiPo batteries.
Posted by Ribble |
May 13, 2012 @ 10:47 PM | 3,366 Views
Toy 2-LED Dragonfly for V911 night flying.
SIZE: The propeller part is the same diameter as the V911 blade diameter. The blade hub slides firmly down over the V911 flybar.
LEDs: Easily disassembled by gently pulling the plastic pieces apart. The electronics are two LEDs, one on each side, a core of three AG1 Button Cell Batteries (alkaline 13mah), and a very strong eyelet screw that turns into the batteries connecting one set of LED leads to the battery. Eyelet screw switch works very well to turn LEDs on and off, so precise it can even be set to switch on vibrations.
The LEDs are parallel with the battery and are actually blinding at arms length. They are the floodlight kind, 4 inch circle at 1 foot distance, another 8 inch circle at 10 feet, 3.14 volts across the LEDs, eyelet is (-). No resistor. Non-blink blue LEDs on the one I pulled apart. Two LEDs lit, no heat.
Each LED (+) end will slide out of the plastic leaving the other LED still functional. Each LED (-) end unwraps from the eyelet with a half twist.
NOW THE GOOD PART.
The LEDs must have internal resistors because they work fine across a V911 stock battery. No heat, just blinding light. And no damage if you connect backwards.
So, for $0.38 each, you get two floodlight LEDs with internal resistors and a 3 cell battery. Tape a few of these units to the v911 for night flying and when the battery is dead, wire the LEDs to the LiPo 3.7 volt battery.
The FS-CT6B transmitter is a cheap way (about $35) to try something other than the V911 stock transmitter.
One place has pre-order for $27 (Stock: -1017) buy Mode 1 or Mode 2 versions. "4-Model Memory" actually means "4 Mode Memory" as in Modes 1,2,3,4 selectable. No "Integrated timer". No "Contrast Adjustment" - no contrast to adjust.
It does not have Rudder Expo.
It does not have digital trim tabs. But the manual trims can be set instantly without delay and without looking at the transmitter.
This transmitter requires a PC to modify any of the channel variables, including mixing and servo reversing.
It takes eight AA cells. But may have more output power than the stock V911 transmitter.
No model memory. With a computer, you can save and load model types quickly.
On the good side, you can actually buy FS-CT6B transmitters and they are easy to program with little knowledge about how to do it. You can also fly the V911 to see what changes do while programming.
Posted here are my latest settings for the V911 and I am starting to like this FS-CT6B with the V911.
Rudder is set for about 50% of stock. Smooth rudder control that works well with the crazy way that I fly (wind surfing).
The two knobs control Elevation and Throttle starting points anywhere in the full range.
"Purchased a IRF1405 mosfet from the local electronics store and fitted it..I tried it with the receiver out of the helicopter and it appears to work ok.The only problem I had was removing the original mosfet. I haven't done this sought of work for some years and I am a bit rusty."
IRF1405 should work as a replacement for any Syma or Double Horse receiver board.
Note: Input control Voltage Gate to Source is 5.0v for 20 amps motor current, though it does start switching ON between 2.0 and 4.0 Volts.
Posted by Ribble |
Feb 23, 2012 @ 02:25 AM | 3,574 Views
Motor Amps using battery MAH rating and flying time
Calculate motor amps from flying time
Motor amps ?
If you start with a full battery and get an accurate time how long the battery lasts, you can figure out the average current that the motor drew during those minutes.
Amps = (mah) x (1amp/1000ma) x (60minutes/1Hour) / (RunMinutes)
Amps = (mah) x (60/1000) / RunMinutes
Amps = 0.06 x mah/minutes
Example: Amps = 0.06 x mah / Minutes
Amps = 0.06 x 1000 / 6 = 10 amps average current
Amps = 0.06 x 1000 / 3 = 20 amps average current = 1000mah battery that lasts 3 minutes
Amps = 0.06 x 1300 / 3 = 26 amps average current
Amps = 0.06 x 1300 / 4 = 19.5 amps average current
Amps = 0.06 x 1300 / 5 = 15.6 amps average current
Amps = 0.06 x 1300 / 6 = 13 amps average current
Amps = 0.06 x 2000 / 6 = 20 amps average current = 2000mah battery that lasts 6 minutes
Amps = 0.06 x 2000 / 3 = 40 amps average current
Amps = 0.06 x 680 / 6 = 6.8 amps average current
Amps = 0.06 x 680 / 3 = 13.6amps average current
Amps = 0.06 x 900 / 6 = 9 amps average current
Amps = 0.06 x 900 / 3 = 18 amps average current
Well, more or less. Pick a ratio of MAIN/TAIL and apportion the total amps
A good ratio may be 3/1 where main = 75% and tail gets 25%