For sale are polycarbonate domes for DJI F450 & F550 frames, as well as Rusty's UAP1 & UAP2 frames. The cost is $25 plus shipping for a standard hemisphere dome or $29 plus shipping for a hemisphere dome with a removable GPS sensor protection/mounting pocket.

You can order online at www.BadgerFly.com, or PM me if you are interested.

DJI F450 frame hemisphere dome dimensions: 135mm inside diameter, 68mm from flat flange to inside top of dome, 158mm diameter of flat flange.

DJI F550 frame hemisphere dome dimensions: 152mm inside diameter, 76mm from flat flange to inside top of dome, 185mm diameter of flat flange.

UAP1 frame hemisphere dome dimensions: 134mm inside diameter, 67mm from flat flange to inside top of dome, 161mm diameter of flat flange, 5mm vertical flange lip.

UAP2 frame hemisphere dome dimensions: 174mm inside diameter, 87mm from flat flange to inside top of dome, 208mm diameter of flat flange, 5mm vertical flange lip.

0.080" thick (2mm) clear polycarbonate domes are very strong to protect those expensive electronics. Polycarbonate (Lexan, Makrolon, etc) is the strongest plastic and won't shatter like acrylic, PET-G, and other clear plastics that you can buy at a cheaper price. These are the real deal if you care about your electronics!

The domes can be mounted using velcro, 2-sided tape, screws with standoffs, wire ties, etc.

These hemispherical domes can be purchased alone or with an optional GPS sensor unit pocket. The...Continue Reading

This is what I am flying with at the moment:

XHex 1:

Rusty’s XHex UAP1 frame with 5/8” OD carbon arms
BadgerFly custom polycarbonate protection dome
Rusty’s tube legs landing gear set
HoverFly Pro V2 black board
HoverFly GPS board
GS407 GPS Sensor Module
Avroto M2814-11S short shaft motors
Turnigy AE-30A ESCs with BLHeli firmware - all center power wires removed
6x Turnigy Rx-Servo signal boosters between board and ESCs
Homemade “spider” power distribution
APC slow-fly 11x4.7 props
Futaba R6008HS 8-channel receiver
HKU3 5V 3A UBEC power for receiver
Turnigy 4S 6000mAh 25-50C nano-tech batteries
Rusty’s floating camera mount with 6 soft threaded dampers
Rusty's UG1 2-axis gimbal with Hitec HS-7955

Futaba T10CHG radio transmitter

Weight without battery: x lbs yoz ( gms)
Weight with battery: x lbs yoz ( gms)
Flight time: approx x minutes (+/- 30 sec)

XHex 2:

Rusty’s XHex UAP1 frame with 5/8” OD aluminum arms
BadgerFly custom polycarbonate protection dome
Rusty’s tube legs landing gear set
HoverFly Pro V1 green board
DPCAV L-C board power supply filter modded w/ 25V 1000uF capacitor for 4S batteries
AX-2810Q-750KV motors
Turnigy AE-30A ESCs with BLHeli firmware - all center power wires removed
6x Turnigy Rx-Servo signal boosters between board and ESCs
Homemade “spider” power distribution
KX-171LV-N low voltage FPV camera 5-15V DC
5.8GHz 200mV FPV transmitter with IBCrazy’s cloverleaf antenna
AEO 12V 2.5A UBEC power for FPV transmitter
APC slow-fly 11x4.7 props
Futaba R6014HS 14-channel receiver
HKU3 5V 3A UBEC power for receiver
Turnigy 4S 6000mAh 25-50C nano-tech batteries

RC305 5.8GHz AV FPV receiver with IBCrazy’s skew planar antenna
Futaba T10CHG radio transmitter

Weight without battery: x lbs yoz ( gms)
Weight with battery: x lbs yoz ( gms)
Flight time: approx x minutes (+/- 30 sec)

For sale are white and black domes for DJI F450 & F550 frames, as well as Rusty's UAP1 & UAP2 frames. The cost is $12 plus shipping for a standard hemisphere dome or $16 plus shipping for a hemisphere dome with a removable GPS sensor protection/mounting pocket.

You can order online at www.BadgerFly.com, or PM me if you are interested.

DJI F450 frame hemisphere dome dimensions: 135mm inside diameter, 68mm from flat flange to inside top of dome, 158mm diameter of flat flange. Weight: 59 gms

DJI F550 frame hemisphere dome dimensions: 152mm inside diameter, 76mm from flat flange to inside top of dome, 185mm diameter of flat flange. Weight: 75 gms

UAP1 frame hemisphere dome dimensions: 134mm inside diameter, 67mm from flat flange to inside top of dome, 161mm diameter of flat flange, 5mm vertical flange lip. Weight: 64 gms

UAP2 frame hemisphere dome dimensions: 174mm inside diameter, 87mm from flat flange to inside top of dome, 208mm diameter of flat flange, 5mm vertical flange lip. Weight: 100 gms

0.093" thick Hi-Impact Styrene domes are very strong and are paintable.

Hemispherical domes can be purchased alone or with an optional GPS sensor unit pockets. The pocket fits perfectly at the top of the underside of the dome to protect the sensitive GPS unit or other electronics that need to be mounted above the flight control board. It can be attached with velcro or with nylon or aluminum screws (steel screws will affect the GPS signal). The...Continue Reading

For Sale - 4-arm helping hands solder tool to make soldering tasks easier and more precise!

The base is made from 6"x4"x1/2" thick aluminum, so it won't tip over, and won't burn from the solder. In addition, there is a non-slip layer of cork on the bottom to protect your work surface. The arms move easily, but will stay put exactly where you want to position them. The alligator clips hold the connectors and wires firmly and will also rotate 360 degrees. Perfect for soldering connectors and circuit boards.

All brand new and ready to use! I've sold over 50 of these on this forum and others. Check my trader ratings for comments from purchasers.

I usually have several in stock and will sell each for $55 plus postage (USPS Priority Mail) in the continental US fully assembled! I will also ship worldwide. Note that the magnifying glass and Maglight are not included.

Please order online at: www.BadgerFly.com