My new experiment, It's kind of a Bi-Wing MAV with 3 rudders and 2 elevators. 2mm Depron, 6'' WS and the airframe weighs 4.90 grams. I thermal molded the wings airfoil and dihedral. Planning on using a 6400 with the micro J3 Cubs motor/gearbox and a Hyperion 70mah bat.

My first time using EPP, not sure if I like it but I haven't crashed it yet.
KFM4 with 3mm EPP, AR6400, XP-7A, AP03(4000kv) and 2 single cell Hyperion 120's with series harness. Wingspan is 15.25'' Weight is 26gr and RTF 34.75
I overlaid the first 2 pics on top each other and came up with this plane.

Made from 2mm Depron(all I had) with a 17.25'' span. UM Stryker motor and RX with 2030L servos. Just over 38grams and RTF around 50. Colored with Sharpies.

...

17'' WS, 32.70grams, 3mm Depron, DT RX, XP7Aesc, AP05motor, (2) AS2000Lservos, (1) AS2000servo-rudder.Tailerons and Elevons hooked together. Great little flier but has so much control authority I'm using 70 percent expo to tame this puppy down.

17" wing span, just under 37 grams, all S-bach equip,(-2servos)KFM4 with 3 layers of 3mm Depron,Hyperion 180 & 240 batts, 4530 & 4040 props.With the 4530 prop it cruises around nice and smooth but still pretty quick. With the 4040 prop "OMG" my new favorite plane to fly, having more fun with this than the Stryker.

9'' span from 2mm Depron (looks closer to 1.5mm to me) with a Vapor brick and gearbox (with ball bearings,J3Cub motor)and a carbon fiber 5030 prop (shoutchen gave me a great deal on these, can't thank him enough) 12.12grams and RTF with Hyperion 70mha 14.48grams. Heat molded the dihedral in with a wood jig and the oven, worked great. Just did a thrust test and this little setup pulled Just over 28 grams (WOW)

Just under 7'' span, 2mm Depron,11.5 grams, Vapor brick, J3Cub gear box with old Helli motor, and a been to hell and back CF prop. Made this for a fellow flier and we've beaten it up already, thought I'd post pics while it's still in one piece.

MCX Brick with 7mm blue SS motors

1mm Depron wing and 2mm body, Vapor brick, J3 Cub 6mm motor, prop and gearbox with ball bearing.(22grams thrust) 7.75''W x 9.75''L, 12.20grams and a AUW with 70mah bat of 14.75grams

3mm Depron with 5um Corsair Blue Microlite film. AR6400L rx & AS2000L servo, 8.5mm ball bearing gear box with black end bell motor, 170/60 prop, 15.5'' spam & 11'' cord(including elevons) and 28.5gram weight.

,,,...Continue Reading

2mm depron, AR6400L rx, AS2000L servo. XP-7A esc, AP03(4000kv) bl motor, 4530 gws prop, 12'' span, 9.5'' cord, 12.5''lenght, 26 gram weight,

3mm depron,26.67g, 12'' WS, AR6400L, AS2000L servo, 4-Site motor and prop,Mustang GB, 120 or 180 hyperion lipo

...

AP03 brushless motor
XP-7A esc
AR6400 rx
HYP G3 120 lipo

1 and 1.2mm carbon fiber airframe elevators a bit thinner, covering is gift basket shrink wrap from Walmart (I was there it was there so I said what the heck) I'm sure it isn't the lightest but it works. Flies pretty slow and smooth

10 gram motor, XP-7A esc, AR6300, 2-cell Hyperion G3 240, 2.5 gram servos,13'' wingspan,5mm styrofoam body and 3mm wing colored with sharpies.

build 40....Continue Reading

2-cell, 23.71g AR6400 rx, AP03 rewound 16 turns of 32 gauge ABC wind terminated Wye, original had 12 turns for a KV of 4000 , and a 5030 Carbon fiber prop that's been chewed down by cement to 4.75''.
Not sure how much faster it flies now only flew the original a couple of times long time ago, but it cruise around slow and smooth and has unlimited vertically or do countless loops, easy to roll and fly inverted....Continue Reading

different dart patterns i've made and nutballs.
the superman was built just like the nutball (SUPERBALL) and
looked like a bat flying at night....Continue Reading