HobbyKing.com New Products Flash Sale
GallopingGhostlr's blog
Posted by GallopingGhostlr | Feb 17, 2014 @ 03:12 AM | 2,313 Views
Several years ago, I bid and won an original Berkeley Impulse kit on E-Bay. I don't remember exactly how much I paid for it, but I think it was around $40 shipping included. The kit had some water stains on it. The plan was aged from heat. It appeared the kit had been stored in someone's attic for a while.

First, I reconnoitered the situation. I already had a good plan that I bought from Sig in the mid 1990's, when they were clearing out the remaining Berkeley plans they had in stock. It came with the original Berkeley plan envelope. As Kit P16-5 it sold for $1.00 US when Berkeley was still in business in the early 1960's. Of course I paid more for it from Sig, but it was still only a couple bucks.

First impressions of the kit .... it had a lot of die crunched pieces and plywood was the inferior quality Luan, not birch ply of later kits. Accuracy of die cutting left a little to be desired on larger pieces such as the fuselage halves. I started off by cutting out the wing and stabilizer ribs, fuselage sides and formers, then start assembly.

Fit and finish of the fuselage sides were rough. I trimmed as best as possible, but still fell short, ended up splicing a little back to make a solid fuselage side from two pieces. Then pieced together the buikheads. Also removed balsa from the center of the bulkheads to reduce weight. To make room for the fuel tank, I cut out the center of the landing gear mounting bulkhead with a hole saw. To prevent from splitting the Luan, I...Continue Reading
Posted by GallopingGhostlr | Nov 01, 2013 @ 02:44 PM | 1,856 Views
During our last move, the Flitecraft .40 J-3 Piper Cub ARF tail feathers got damaged badly enough to need replacement. I have fabricated replacements out of Borden 3/16" (5mm) thick poster foamboard. This foam board has both front and back covered with a light cardboard with foam in between, so it is rigid.

This ARF kit of a decade ago was partially completed with controls and radio installation remaining. An OS Max .40FP R/C is installed in the nose. The installation manual has since been long lost, but this is a simple model and straight forward enough to complete.

This plane has a 58" (1,473mm) wingspan and a 9-3/4" (248mm) chord giving it a wing area of 565 sq. inches (0.365 sq. m). Being heavier than current ARF's, it should be a fast flyer with good wind penetration.
Posted by GallopingGhostlr | Oct 21, 2013 @ 10:07 AM | 1,861 Views
About a month ago, I received this Great Planes Big Stik .60 from a modeler getting out of the hobby for a song. It had some crash damages that were partially repaired and without engine. Can't say what iteration or year this Big Stik came from. These are the repairs I did to clean it up and fix problems. Explanation is per Photo Number:
  1. Main Gear support broke due to lack of structural support. Only thing supporting lightening hole above is the 3/32 in. balsa side plank, which was mashed from a hard landing.
  2. 3/32 in. plywood shear panel has been installed from Fuselage Bulkhead #4 to support rear landing gear ply mount to nearest load bearing point, Bulkhead #5 at wing rear. Plywood extends to underside of ply servo mounting tray.
  3. 1/8 in. balsa spacer is added to support exterior fuselage side plank. Not shown, 3/8 in. sq. hardwood brace is mounted in notch between 1/4 in. ply landing gear mount and Bulkhead #4 for front landing gear support.
  4. Downloaded GP manual photo shows clunk tank neck filling ply engine bulkhead hole. 12 oz. tank neck is slightly larger due to tank stopper cover support lip, so undersized hole was ground larger to fit.
  5. 3/32 in. balsa planking has been added around main landing gear bottom and sides. 3/32 in. basswood floor has been provided from engine Bulkhead #1 to main landing gear front Bulkhed #3. This provides structural floor support for the radio receiver and battery. Original epoxied to floor balsa block rear tank support held tank in place.
...Continue Reading
Posted by GallopingGhostlr | Feb 11, 2013 @ 01:33 PM | 2,076 Views
An E-Bay buy, the engine suffered tool drawer paint chipping in its previous life as an used engine. Now, the head is all red, with what else? Testors paint.
Posted by GallopingGhostlr | Feb 10, 2013 @ 06:29 AM | 2,490 Views
I prefixed this blog with [b]cool]/b], which I'm sure may bore some not into vintage engines and sound damping solutions.

I needed mufflers for the vintage McCoy and Enya engines. The following is how I solved the problem.

Photos 1 & 2: I had a spare YS muffler. I modified it to fit this Testors McCoy .40 Series 21 CL Black Head. I fitted it by filling the muffler mount holes, cutting a stainless steel hose clamp mounted with 4-40 screws drilled and tapping into the mount ends.

Photo 3: I mounted a Tatone EM-4 Calumet .09-.19 Muffler to an Enya .19-VI TV engine. Since I lacked prop washer and nut, I improvised. I drilled out a fender washer to fit the prop shaft. Nut is a spare from my parts bin.

Photo 4: The Enya ran hot. Photo shows the problem, an overly restrictive baffling system and too small an expansion chamber area.

Photo 5: I ground away as much baffling as practical. It still ran hot.

Photo 6: Solution resulted in converting this Calumet muffler to a Tongue muffler for a Testors McCoy .19 Red Head CL engine for a control line airplane.

Photo 7: On this venerable Enya .09-III TV, I ground the other EM-4 Calumet's mount lip to clear the cylinder. Because the .09 is left hand exhaust required the muffler to be mounted upside down. The baffling system is very restrictive, leading to what I am told many an engine ruin due to overheating, which my testing proved. Further modifications are pending.

Photo 8: Solution for the Enya .19-VI TV is the Tatone .29-.40 Peace Pipe Muffler. It ran cool and powerful with this muffler.

There are ways to take sour apples and turn them into apple sauce.