HobbyKing.com New Products Flash Sale
dmrcflyr2's blog
Posted by dmrcflyr2 | Yesterday @ 06:39 PM | 1,212 Views
So I get these two engines and neither one runs. One engine is new but has a 'crack' in the head near rocker arm mount. The other is some pretty war torn engine. Between the two one good engine should result. Right? I took both apart starting with the used engine.

It was pretty dirty and had evidence of lots of run time as seen in the carbon deposits on the exhaust valve stem and face. The piston ring was worn into the piston head and I do not think they could ever be separated. The PO had installed the head from this engine onto the new engine. So this had the new head on it. I was so into the disaeembly that I did not take many pictures of the internals. I removed the valve cover and noticed a broke, sheared off rocker arm mounting lug, not a 'crack'. This head is toast. Strip the valves, springs, etc. and begin the clean up of the used head.

The new engine was just that a NEW engine with a used head installed. So I did not completely tear this engine down. I just removed the head and installed the cleaned up used head. I installed all of the new head hardware and tightened it all down. Set the valves and viola! Ready to run for the first time.

She runs!!

Enya 80-4C First run.(1) (1 min 22 sec)


...Continue Reading
Posted by dmrcflyr2 | Yesterday @ 09:29 AM | 1,038 Views
Here are a couple of videos of the FA-56 that I got yesterday. I ran it for the first time. It fired right up and holds a nice idle of 2255-2400RPM with an APC 12x6 propeller. Mogan's Omega 10%.

During the cleaning I had removed the needle valve. It was set at 3.5 turns open. I reset it to 2.5 turns open and this is how it ran at that setting. The first video it topped out at 10,400 RPM. I eventually opened the needle so that WOT was about 9800-9900 RPM on the stand.

This is true Saito perfection and quality.

Initail start up (1 min 33 sec)

...Continue Reading
Posted by dmrcflyr2 | Yesterday @ 08:17 AM | 1,105 Views
So back around Christmas I posted that I had scored a nice NIB Saito 56. Then in my search for the perfect NIB Enya 53-4C, I sacrificed the 56 in a straight trade. So I began another search for a 56 to replace it. I wasn't too concerned about getting a NIB one, but would if the opportunity presented itself. It did not, but I did find a very nice used 56 from a member here.

A 2 digit monetarty score and I have another very nice Saito. As usual with used engines I get, I opened it up to determine it's true usage and condition. I found it to be a used engine that seemed fully broken in. It had spent quite some time in a sideways mounted position, by the pooling/staining of the right side of the backplate cover and crankcase. It had never been opened up before. I could tell by the torque on the screws and the lack of marks on the rocker arm screws. Those screws are always so tight there is most often some burring on the slot if it has been opened up. Finding the exact thickness blade that is narrow enough to fit inside the slot is tough without grinding a screw driver down.

The intake valve was a bit loose > .10mm, but the exhaust valve was right on. The upper end, rocker arms and valve spring area was dry. Apparently it had never been lubed by the owner. The valve cover gaskets were dry and broke when I opened it up. No worry, I usually remove those gasket anyway. It is not like tons of oil gets up there and even if it did and I saw a small amount seeping...Continue Reading
Posted by dmrcflyr2 | Jan 19, 2015 @ 05:53 PM | 1,465 Views
With the 11 engines I have right now I would say only 3 of them are FULLY broken in. I have had numerous engines in the last 3 years. Some come and some go and in my desire to acquire NIB engines I sometimes forget how nice it is to have fully broken in engines. They include my Saito FA-45S, the Enya 60-4C, and the Enya 46-4C. Today I took the 46 out of the box and put it on the stand for a quick tank.

I am not a member of a flying club at this time; I let my membership lapse at the Largo Flying Field. Just too many electric fliers there and glow powered planes are looked down upon. Soon I will be joining SPARKS where I had a membership 10 years ago. At least there glow and gas powered planes are welcomed.

So I had removed the 46 from the Tower Uproar it had flown since I bought the engine in 2013. I am unsure how much run time was on it when I bought it but I have put some fuel through it on the Uproar.

On the bench, after prime, 2 flips and it was running. I had taken the needle valve out for storage so I had to reset it. Using my tach, I got it turning the 11x6 prop over 10,000 RPM. In fact it hit 10,500RPM and then I backed it back down to 9800RPM for the bench run.

I have to admit, in the past I have owned many more Saito's than Enya engines, and I cannot ever remember feeling so confident about an engine just sitting at idle for extended periods than I have with these Enya's. I mean the 60 and 46 I can pull the throttle back all the way to the...Continue Reading
Posted by dmrcflyr2 | Jan 18, 2015 @ 11:43 AM | 1,289 Views
So I put both the Enya and the Saito on the bench today for a quick tank before football comes on. I'm telling you that Enya is one of the best looking engines I have ever owned. Compared to the Saito it is a sweetheart too. Now obviously it doesn't have the same compression ratio of the Saito, 7.5:1 vs 9.82:1 of the Saito, but it does make it a bit less dramatic in hand starting.

That damn Saito, or should I say, those damn Saito engineers. I do not understand why they chose to eliminate the throttle stop screw on the carbs for the 91S. Most, if not all, other Saito engines have this. On the test stand it becomes a big deal, as I cannot see or tell how far the throttle is closed before it dies. Not to mention setting the idle. Anyway, this guy bit me yesterday. Numbed the tips of my fingers for a few minutes.

So I ran both and they both performed flawlessly, less the starting issue on the Saito.

They videos can be viewed here.

Saito 91 running (1 min 0 sec)

...Continue Reading
Posted by dmrcflyr2 | Jan 10, 2015 @ 12:42 PM | 1,517 Views
After a two year search, I finally landed the elusive Enya 53-4C and NIB! It cost me a NIB Saito FA-56, but I am good with that. I have had several 56's and they are plentiful. This on the other hand, not so plentiful. Especially this one. This is one of the early ones that includes everything under the sun. Glow plug, remote ignitor, tools set, but yet oddly no feeler gauge. No matter I have plenty of them.

I have been running the 46 and 60 today, so I'll leave this one in it's pristine state for a bit longer....Continue Reading
Posted by dmrcflyr2 | Jan 03, 2015 @ 07:51 PM | 1,529 Views
So I quickly opened the rocker cover and checked the valves. I had set them prior to the first runs. The intake was a bit looser but the exhaust was the same.
Posted by dmrcflyr2 | Jan 03, 2015 @ 11:04 AM | 1,276 Views
Well I did it, I strapped it to the bench and ran 2 tanks thus far. I am impressed, but not surprised. It literally started on the very first flip of the prop. Got to go to lunch now.... will add to this a bit later.

Ok, I just ran a third tank through it. The first two I had the needle valve set so rich that at WOT I was getting only 6000 RPM and 7000 RPM respectively. On the third tank I leaned it to 8000 RPM at WOT. I also began to adjust the idle on this tank. I have the airbleed set to hold a nice 2880 RPM with a nice transition.

I am running Omega 10% and a Master Airscrew 14x6 prop.
Posted by dmrcflyr2 | Jan 01, 2015 @ 12:14 PM | 1,524 Views
The current family picture.
Posted by dmrcflyr2 | Jan 01, 2015 @ 08:53 AM | 1,651 Views
The engine had have wanted for a long time finally arrived yesterday. I was excited all the away up until I pulled it's hulking mass out of the box. This thing is HEAVY. I have loved Enya engines for many years in the smaller sizes. believe it or not this is the first time I have actually held a 90 or 120 size engine in my hand. Sure I have seen them bolted to the fronts of airplanes, but never held.

Well I must say it is a nice LOOKING engine and I am sure it runs well, but I am unsure at this moment if I will ever install it into an airplane. Several reasons:

1. I really do not build much anymore.
2. I do not really fly planes this size anymore.
3. Most modern ARF's of today could not accomodate this engine.

My first and 3rd points have to do with quality of construction of the airframe. It does not take a genius to figure out that any airplane this engine will be strapped into needs a VERY beefy firewall. Ones you can really only get by making them yourself. I have seen enough modern ARF's, having owned a few, to know that the quality of the wood, specifically plywood, is quite inferior and substandard to the aircraft grade you will find and use in kits.

As such I can keep this engine as a shelf beauty for x number of years and run it on the test stand as I do with so many of my engines, or I can sell it and try score the elusive NIB Enya 53-4C. Or heck, just buy another Saito. They seem to be on the for sale list literally ALL the time. Not...Continue Reading
Posted by dmrcflyr2 | Dec 26, 2014 @ 09:55 AM | 1,542 Views
I was taking some comparison pictures of my FA-45S and the new 56 I just got. Seeing as they are the same size crank case, I wanted to see what all physical differences there were between the two.

I also figured since it was out I would put it on the stand and run a tank through it. It started on the 3rd flip. I had a MA 11x6 propeller and Omega 10% fuel.

I recorded 10,500RPM @WOT and a nice 2400RPM steady idle. This is one sweet running engine and the one Saito that I have the most run time on. Although I am not sure how much it really is. It is also the engine I have had the longest; I think I bought it around 2000.
Posted by dmrcflyr2 | Dec 25, 2014 @ 06:41 PM | 2,139 Views
So I had a very nice xmas, I just recieved my NIB Saito FA-56. I am finally getting all of the engines in the condition I want them in for my collection and long term possession.

I am currently looking for a very good to NIP header and cannister muffler for this engine as I am most dis-satisfied with Saito's latest design. I do not care what it sounds like, it looks like crap. Don't care if it provides a performance boost, not sure if it is supposed to, it is hideous! Period.

Anyway, not sure when I am going to fire this engine up but obviously it will not be until I get a new header and muffler.
Posted by dmrcflyr2 | Dec 23, 2014 @ 01:20 PM | 2,519 Views
I strapped my newly acquired 91S to the test stand today for its inital few runs. Normally I am a stickler about adhering to the manufacturers break-in instructions; however I do not necessarily agree with what Saito states.

First they state for a 91 open the needle valve 2 1/2 full turns from closed. I open it 3 full turns. Then they state do not run the engine above 4000 RPM for the first 10 minutes of operation, but they do not state whether or not this 4K is acheived @WOT with the needle valve or the intial needle settings and only run 4K using the throttle setting. Most manufacturers state to run at WOT and achieve the RPM range with the needle valve.

Either way this is what I did: Open 3 full turns and run the engine at various throttle settings througout the fuel tank(s). I assure you 3 turns open is a VERY rich setting. I did not allow the RPM to go above 8000 max on the first tank. I was using a Master Airscrew 14x6 propeller.

I have been breaking in Saito engines since 1991 and I have never had a premature failure, or any failure of any kind on one. So I am quite sure my procedure will yield a favorable result again.

This engine started on the first flip and ran like it had already been run before. Sure it will benefit from a bit of leaning in a few tanks, but it ran quite well. It would hold a steady 3300 RPM idle on this initial tank too. I ran 2 tanks in total today. There was a nice cloud of white exhaust drifting through the neighborhood...

I was comparing this engine to my 65 a few days ago. I took the carbs off of each and compared them side by side. You can see how different they are, and the throat size of the 91 is enormous.
Posted by dmrcflyr2 | Dec 22, 2014 @ 10:12 AM | 2,045 Views
It had to happen some time; I could not let this engine sit around forever. I just put 2 tanks of Omega 10% through the engine. I strapped an APC 10x6 on it , swapped out the glowplug that was in it. It was not a standard Enya plug, in fact it looked like a Fox plug with a big idle bar. I typically do not run plugs with idle bars in ANY engine unless absolutely necessary. It was not in this case.

Following the instructions for starting and break-in, I put about 5 drops of fuel into the carb and flipped the prop several times. It took exactly 1 flip for this engine to start!! I had the needle valve set to 3 turns out which was a bit much.

Using my tach I leaned the mixture until I had 8500 RPM @ WOT. This may sound like a lot but it was still blubbering rich, although it would run without the ignitor on.

Tank 2 I leaned it to 9000 RPM. I will run sesequent tanks leaning slightly each time until I get to about 11K-12K RPM. The listed RPM range for this engine is 8K-16K RPM. I do not fly pylon racers or anything like that so I will not lean this above 12K PRM on the ground for general flying.

I had the air bleed screw set to the mid way closed setting, a good setting for any air bleed carb to begin with, and the engine would hold a very nice 3000 RPM idle. Transistion was not ideal as yet but it is just the first few tanks. At no time did the engine stall or hesitate at all through the runs. I would hold WOT for 10-12 seconds and then drop to mid to low for 10-12 seconds.

All and all just another high quality Enya engine!
Posted by dmrcflyr2 | Dec 21, 2014 @ 01:29 PM | 1,949 Views
Man I love this forum! Since I got back into the hobby in 2012 I have scored some really killer deals on engines, particularly 4-stroke engines. To date I have not paid over $200 for any engine. Now some of the deals came from RCUniverse but still.

Since 2012 I have bought the following NIB engines. Not a single engine cost more than $200 shipped to me. Now I don't still have all of these engines as I like to horse trade, but the point is great deals are available to those who search.

Saito FA-65 - local craigslist have run several times to include yesterday.
Saito FA-91 - RCGroups still have not run
OS FS-90 - From RCU still have not run.
Enya 80-4C - From RCU still have not run.
Enya 60-4C - Recieved in trade, and have now sold.
OS FS-70 Surpass - traded straight deal for Enya 60-4C
Enya 90-4C - Has not arrived yet
Saito FA-56 - Has not arrived yet.
Enya SS 40BB(2) - ran run for 15 tanks and sold it. Just bought another
Saito FA-45 - sold

That is just some the NIB engines, I have not even listed the other used engines I have bought, run and sold. Some of those would be

OS-FS-90 (2) - both sold for other things.
Saito-FA56 - sold in an airplane deal
Enya 46-4C - still around will never sell
Saito FA-50 - sold

I guess the point of this post is that this is a great forum to obtain engines from and all states. I am partial to the older style engines from the 80's and 90's.
Posted by dmrcflyr2 | Dec 20, 2014 @ 11:40 AM | 1,766 Views
So I pulled my prized Saito 65 out of the box a few days ago for a touchy feely session and noticed that it was a bit stiff turning over the crankshaft. Likewise the carb arm too was a bit stiff. Apparently I had not properly shut it down and/or put enough MMO in after its last run. My bad. I put some my MMO in through the breather and rotated the crankshaft around numerous times with a prop on it.

Then I figured, what the heck, I'll just run it again this weekend, along with the Enya 60 I picked up recently. Sort of a side by side RPM to RPM evaluation.

So I strapped the Saito onto the bench first.

It started after the proper prime on the first flip. Once it warmed up a bit I recorded the tachometer readings:
9150 RPM WOT
2610 RPM idle.

The Enya 60 started on about the 3rd flip after prime and recorded the following:
8500 RPM WOT
2200 RPM Idle
I believe that I stated in an earlier post on this engine that I would put some gasket sealer on the front end before running. Well guess what? I didn't. As it turns out the front end did not leak a bit during either of the runs. Unsure if that is just a testament to the machining process for the Enya engines or if I just got lucky. Now I did see some seepage of what I believe to be oil from around the head connection. At least I could see moisture of some sort dancing around while it was running. But there was quite a bit of condensation from the intake manifold too.

Both engines were running the same 13x6 Master Airscrew propellor.

Videos can be seen here:
http://s134.photobucket.com/user/dmr...of%20the%2060s
Posted by dmrcflyr2 | Dec 10, 2014 @ 05:58 PM | 1,697 Views
I have just recieved the second Enya SS 40BB I have owned. I sold the first after it had been broken in on the bench. This one will never be sold. There is just something about the Enya engines that screams quality and this engine is an example of that.

No longer made this late 80's design, I believe, features a cast iron hand lapped piston which when broken in properly broken in will last an indefinite period of time. Dual ball bearing supported crankshaft easily accessed with the front end removed. There is no removeable backplate on this engine, just the front end. The machining is second to none and the simple yet tried and true air bleed carb makes tuning a piece of cake. This is certainly not the strongest 40 sized engine out there but the quality and simplicity of design make it a classic.

As soon as I sold my first I regretted it, I won't be making that mistake again.
Posted by dmrcflyr2 | Dec 06, 2014 @ 03:23 PM | 1,958 Views
So I had sold several other engines and an airplane to purchase my Christmas gifts to myself. I also recieved in the mail today a NIB Saito FA-91S that a wonderful member on this forum parted with. It is about 98% complete, but for the price I cannot complain. The few items missing are the prop washer, proper prop nuts and the 12mm x 14mm box head wrench. The wrench I have plenty of and the prop washer and nuts can be obtained from my LHS, so no problem at all.

I can tell this engine has never had a drop of fuel through it by the look, feel, and smell of it. I actually sold a well used no box FA-91S to help fund the NIB one I was looking for.
Posted by dmrcflyr2 | Dec 06, 2014 @ 03:05 PM | 1,916 Views
So I picked up another nice deal here from a fellow member on this forum. A very WELL used Enya 60-4C, for $50. It was engine only no box, tools, or exhaust. There are very high resolution pictures in the ad so I knew what I was getting.

I immediately began the normal tear down. It seemed to have decent compression. Numerous dings and clear signs of good solid use.

With the front end off I immediately could tell this was not the original set of bearings in this engine. The front was a sealed kind, sealed on both sides which is usually not done. The rear looked good and both felt ok. Although the front had a bit of damage; the front seal was pressed in a bit. The crank shaft, amazingly, tapped right out of the front end leaving both bearings in place. I quickly and easily tapped the front bearing out to better inspect it. It will do for now. I also saw some damage inside the front end from when the rear bearing had been removed. A pretty nice chunk of the bearing shoulder was taken out. We will see how this affects operation, but it should be alright. That can be seen in the last picture.

I did not remove the valves as they felt nice and smooth with no sticking at all. When I removed the rocker arm holder I found the head screw beneath it was not torqued at all.

The piston came right out and had no dark areas on it at all. The view of the valves showed some running but no hot spots or excessive carbon build up. It looked pretty darn good really.
...Continue Reading
Posted by dmrcflyr2 | Nov 30, 2014 @ 12:30 PM | 2,204 Views
I have owned this engine for about 3 years now. I am pretty sure that I bought it here but I cannot find the deal. Maybe I got it from RCU, either way it was a used engine in excellent shape when I bought it. It has been on my Tower Uproar 40 for the last 2 years and logged about 15 flights. It has been nearly a year since it was run last so I thought I would take it off the airplane, clean it up, and prep it for storage. I am not flying anymore so it needs a good prep before storage.

I took the front housing off to see the bearings and crankshaft. The bearings still felt good and the crank shaft easily tapped out with a rubber mallet without heat. The front gasket is gone, deteriorated. When this gets to run again I will pop the front housing off again and seal with Permatex Motoseal gasket maker. Until then, I'll leave it.

The head and valves look like new still. I cleaned the inside with standard rubbing alcohol followed by being blown out with the air compressor. A nice coating of Marvel Mystery oil for the insides and bearings. Final assembly and turn the prop over. No compression... No problem. Even though I did not disassemble the rockers from the center piece, nor did I remove the timing housing, the valves still needed a bit of adjustment. It had compression when I removed it from the plane, but in the process of disassembly the timing changed a bit. Maybe the screw holding the rockers in place was not properly torqued. Each arm was a bit...Continue Reading