Some of my boat designs

[forresterace]

Just to get some things rolling, I'll post a few pictures of some of my raceboat designs.

The first is a "P" Sport Hydro (12 cell)

[forresterace]

Same boat, different angle

[forresterace]

Offshore Mono

[forresterace]

Offshore Mono 2

[forresterace]

"Q" Offshore Catamaran

Doug Forrester
Forresterace Designs

[Dick Crowe]

I've seen that more then a few times. Very nice and as fast as it gets. I'm pretty sure the fastest P Sport I've ever seen was when Brian Vega ran your boat at the Alaska Nats.

Here are a few of mine

My favorite! - My old beat up Maus O Sport Bardahl. That boat fits me like a glove! It may get retired soon though. Andrew has a new boat one click off of this one that fixes a few quirks.
http://www.drcwebservices.com/boat_stuff/bardahl1sm.jpg

Latest project! SS1 OPC.
http://www.drcwebservices.com/boat_stuff/DPI12cellopcsm.jpg

This is the sister ship to Larry Larsons. I built 2 in 1990 and gave one to him. I may have to drag out my templates again. It's been a long time since I've built a boat from scratch and could use a little ca on my fingers!
http://www.drcwebservices.com/boat_stuff/1990osport1sm.jpg
http://www.drcwebservices.com/boat_stuff/1990osport2sm.jpg

See ya,
Dick

[JimClark]

Doug I knew you had designed a few boats but I really had not seen them. The pictures you put up are beautiful and i am sure they run as well as they look.

Jim Clark

[JimClark]

Dick what is the white pickelfork? Who's design?

Are the littleones still hanging in there?
Jim Clark

[Dick Crowe]

That's my design Jim. I used to do a lot of boat building and experimenting about 10 years ago. That boat is the end product of a pile of mistakes. I still had 2 and gave one to Larry Larson who has set every sport straightline record there is with his. O Sport, P Sport and LSH.

I tried mine in 2001 at the saw's with 4 cells but couldn't match the speeds of the little riggers, although it was running in the low 40's.

See ya,
Dick

[Twmaster]

Hii guys! Nice to see you all over here too :)

Doug, what is the size of the white offshore??

Cheers,

Mike N
El Whacko

[forresterace]

Hi Mike
It's 22" long with a 6" beam. Steve Reesor built a 27" version of it (now owned and raced by LOU) last year.
I plan to increase the deadrise to 25 degrees and build a 31" long version for "Q" Offshore this year.

Doug Forrester
Forresterace Designs

[Twmaster]

That's a very sweet looking boat Doug. Nice size too. LOU is a lucky fellow!

Cheers,

Mike N
El Whacko

[RCRandy]

Well, they will let any one on this board. any way this is my new hot shot

[JimClark]

You are right Randy they even let me join!!!!!!!!
Jim Clark

Originally posted by RCRandy
Well, they will let any one on this board. any way this is my new hot shot

[forresterace]

Hey Guys

It was Groucho Marx that said - " I wouldn't belong to a club that would have me as a member"

:D :D :D

Doug Forrester
Forresterace Designs

[Climate]

A couple of 6-8 cell riggers.

http://www.climateboatworks.com/pictures/ff6cellandblizzard.jpg

Peter

[Trent Hare]

Hi gents,
I couldn't resist...

Here's my sport hydros -
http://www.autoimages.com/boatpics/micro_sports.jpg

[RCRandy]

Hey Trent your boat is on the new DMWB header. check it out

The Devil Mountain Water Boilers Web Site

[forresterace]

Hi Trent
As usual, they are gorgeous. Are they: 4 cell on the left and
Micro on the right. Do you still have the Hacker B40 in the micro?

Doug Forrester
Forresterace Designs

[Trent Hare]

Hi Randy,
I'll have to check that out- cool!!


Hi Doug,
Yep, that is the old 4 cell beast - which is now run in 6-7 cell classes with a Lehner 5300 Basic. I like the 4 cell class, but after running a brushless motor - I don't want to ever go back to running brushed car motors... ;)

The MicroSport is still running a B40-13S size motor. It handles the load much better than the B20's. It's actually faster too! The 1700AUP's (7 cells) are the cells of choice.

[Dennis Whitt]

If you ever bring those boats to a race,Ill snatch the trophy from the table hand it to you ,pack up my junk and take it back to the room and just be content watching twenty year old movies on HBO reminesing about the good old days!!!!

[xsvspd]

Doug, could you possibly send me plans for the cat...Been looking for some cat plans for the longest...could it be converted to nitro...Rich

[Mark Gund]

Hey Guys

It was Groucho Marx that said - " I wouldn't belong to a club that would have me as a member"

:D :D :D

Doug Forrester
Forresterace Designs Or,I would like to join a club and hit someone over the head with it! :D

[alwhorley]

Hey Guys

It was Groucho Marx that said - " I wouldn't belong to a club that would have me as a member"

:D :D :D

Doug Forrester
Forresterace Designs

Actually, if Groucho said it he was quoting Mark Twain ;)

[Warren2008]

Hello Everybody,

We are very pleased to get the opportunity to contact you at the moment, thanks a lot for your much working!

First of all, I would like to give a brief self-introduction for you. Our company is a Chinese supplier which is specializes in manufacturing and exporting all kinds of toys for a few years. Especially the high quality toys as Radio Control Toys and Hobby Products. I would like you to take a minute to browse our website( http://www.gr-exp.com ) to know more about us. I would like to offer a price list of our products for you, but please inform me the products items or products name which is your requirements,Then we will provide further information for your reference.

Due to our high quality products, competitive prices, and excellent service, our products have sold well in a variety of markets worldwide. We wishes to meet your requirements and exceed you expectations. If you are interested in any of our products, please do not hesitate to contact us. We look forward to your inquiries and orders in the near future.

I would really appreciate for your cooperation and your kind help!

Best regards!

Yours Truly,
Warren

[pacro]

do you think I could get a plan or something for the offshore Mono Mania boat

[speedchaser]

All I can say is, you should go into business full time... This must be one of the best cases of 'B.S & D.I.R'. Brains, Style & Doing It Right! What cutting tools do you use to get the edges to meet/join so accurately? Now I know I'm fed up with my 600 can size, 8 x 2000mah, 25" V hull! It just about touches 24mph. You've given me inspiration to go for a 30" external tube-drive tunnel hydro...
Great work. :cool: