9zh wc

[Stuart Robinson]

Dues anyone now how I can change from mode 1 to mode 2
Regards
Stuart

[Glenn Asquith]

Open the back CAREFULLY.

After marking all the ribbon leads, GENTLY remove them and after undoing the
screws, remove the board.

Swap the brass plate and the spring arm over.

Go into the radio, go to FNC, and swap the elevator/throttle settings eg t3
to t2, j3 to j2 and vise versa.

Or take it to a techy, if you have one handy that knows radios well.

Glenn
Sydney


"Stuart Robinson" <robbo5th@bigpond.com> wrote in message
news:NRm5a.52431$jM5.132390@newsfeeds.bigpond.com. ..
> Dues anyone now how I can change from mode 1 to mode 2
> Regards
> Stuart
>
>

[Tim van Halteren]

I heard that it did also involve recalibrating. And you need to have access
to the hidden service menus for that. I this true?

Tim



"Glenn Asquith" <gasdNOSPAM@optusnet.com.au> wrote in message
news:3e56a45e$0$19975$afc38c87@news.optusnet.com.a u...
> Open the back CAREFULLY.
>
> After marking all the ribbon leads, GENTLY remove them and after undoing
the
> screws, remove the board.
>
> Swap the brass plate and the spring arm over.
>
> Go into the radio, go to FNC, and swap the elevator/throttle settings eg
t3
> to t2, j3 to j2 and vise versa.
>
> Or take it to a techy, if you have one handy that knows radios well.
>
> Glenn
> Sydney
>
>
> "Stuart Robinson" <robbo5th@bigpond.com> wrote in message
> news:NRm5a.52431$jM5.132390@newsfeeds.bigpond.com. ..
> > Dues anyone now how I can change from mode 1 to mode 2
> > Regards
> > Stuart
> >
> >
>
>

[Richard]

Yes you need to recalibrate the transmitter.
Look on www.model-gadgets.com


"Tim van Halteren" <t_dot_van_dot_halteren@inter.nl.net> wrote in message
news:3e56aa9c$0$19495$19deed1b@news.inter.NL.net.. .
> I heard that it did also involve recalibrating. And you need to have
access
> to the hidden service menus for that. I this true?
>
> Tim
>
>
>
> "Glenn Asquith" <gasdNOSPAM@optusnet.com.au> wrote in message
> news:3e56a45e$0$19975$afc38c87@news.optusnet.com.a u...
> > Open the back CAREFULLY.
> >
> > After marking all the ribbon leads, GENTLY remove them and after undoing
> the
> > screws, remove the board.
> >
> > Swap the brass plate and the spring arm over.
> >
> > Go into the radio, go to FNC, and swap the elevator/throttle settings eg
> t3
> > to t2, j3 to j2 and vise versa.
> >
> > Or take it to a techy, if you have one handy that knows radios well.
> >
> > Glenn
> > Sydney
> >
> >
> > "Stuart Robinson" <robbo5th@bigpond.com> wrote in message
> > news:NRm5a.52431$jM5.132390@newsfeeds.bigpond.com. ..
> > > Dues anyone now how I can change from mode 1 to mode 2
> > > Regards
> > > Stuart
> > >
> > >
> >
> >
>
>

[acomm]

take a look heer http://www.model-gadgets.co.uk/ and go to the diy section .

trevor

"Stuart Robinson" <robbo5th@bigpond.com> wrote in message
news:NRm5a.52431$jM5.132390@newsfeeds.bigpond.com. ..
> Dues anyone now how I can change from mode 1 to mode 2
> Regards
> Stuart
>
>