ASSAN
May 19, 2008, 09:35 PM
hi, guys,
i am so sorry that we haven't time to transfer the instryment to English.but seems the picture show what the new 3in1 can do.
hope you like it.
meng
Brief Describe：
EBE-II include Electronic Ignition,Battery Volateg Monitor and UBEC, 3 In 1 on board.it’s solid and easy use.espicailly for that with narrow engineer operate space and not easy apply traditional Ignition.
Features：
Swtich control delay engineer start；
LED indicate Ignition working or not；
Line LEDs show batter voltage；
12V or 3s Li-poly pack as power supplier；
Isolate output in UBEC and Ignition；
Short protect；
Anti incorrect input direction；
Work Condition：
Input Volatge：DC 12v
Max Ignition Current：3Amp
UBEC current：3Amp continous,5Amp Max.
Heat Glow Plug time：10s
Idle current：10mA~100mA
Size：80 X 24 X 9mm
weight：20g（not include wires）
－－－－－－－－－－－－
Instruction：
1．Connect the wires and connector as the top picture show. If the input battery with wrong direction, the item will not work only.
2．Power on EBE-II,Battery Voltage indicate LEDs will light all, the system will run self check software first, at this condtion, Yellow LED in GLOW PLUG will light and send power to the Glow Plug.if you don’t want start your engineer at this time, don’t Pull your prop or do any other start prepare action,this is import to keep you outside dangrous.
3．After the self check finished，Yellow LED below GLOW PLUG will down，means EBE-Ⅱ is prepare to work.
4．When you need start your engineer,pull the Switch and lease，RUN LED will light in the same time，you need use your Glow Starter to drive your prop；10s later，RUN LED off and stop hot the Glow Plug auomaticlly.if your start not success in the first touch, fellow the same steps and try again.
5．If you see the SHORT Red LED light,means the cirle with short problem. You need check them and take the battery pack off.restart only at power on again.
6．Battery Volatge show the condition of your battery pack.Green means full,Yellow is in middle and Red means you need charge battery now.
Note: we advise you take a battery pack more than 1000mAh as supplier,because UBEC need huge current when it Power.
i am so sorry that we haven't time to transfer the instryment to English.but seems the picture show what the new 3in1 can do.
hope you like it.
meng
Brief Describe：
EBE-II include Electronic Ignition,Battery Volateg Monitor and UBEC, 3 In 1 on board.it’s solid and easy use.espicailly for that with narrow engineer operate space and not easy apply traditional Ignition.
Features：
Swtich control delay engineer start；
LED indicate Ignition working or not；
Line LEDs show batter voltage；
12V or 3s Li-poly pack as power supplier；
Isolate output in UBEC and Ignition；
Short protect；
Anti incorrect input direction；
Work Condition：
Input Volatge：DC 12v
Max Ignition Current：3Amp
UBEC current：3Amp continous,5Amp Max.
Heat Glow Plug time：10s
Idle current：10mA~100mA
Size：80 X 24 X 9mm
weight：20g（not include wires）
－－－－－－－－－－－－
Instruction：
1．Connect the wires and connector as the top picture show. If the input battery with wrong direction, the item will not work only.
2．Power on EBE-II,Battery Voltage indicate LEDs will light all, the system will run self check software first, at this condtion, Yellow LED in GLOW PLUG will light and send power to the Glow Plug.if you don’t want start your engineer at this time, don’t Pull your prop or do any other start prepare action,this is import to keep you outside dangrous.
3．After the self check finished，Yellow LED below GLOW PLUG will down，means EBE-Ⅱ is prepare to work.
4．When you need start your engineer,pull the Switch and lease，RUN LED will light in the same time，you need use your Glow Starter to drive your prop；10s later，RUN LED off and stop hot the Glow Plug auomaticlly.if your start not success in the first touch, fellow the same steps and try again.
5．If you see the SHORT Red LED light,means the cirle with short problem. You need check them and take the battery pack off.restart only at power on again.
6．Battery Volatge show the condition of your battery pack.Green means full,Yellow is in middle and Red means you need charge battery now.
Note: we advise you take a battery pack more than 1000mAh as supplier,because UBEC need huge current when it Power.