20 x T-REX 450 Main Shaft FREE for you guys!

[HKAero-Nuts]

We just got the NEW SupremeHobby T-rex 450 main shaft.
For more information please visit here : http://www.aero-nuts.com/product_info.php?products_id=486

http://www.aero-nuts.com/images/SupremeModel/SMShaft1.jpg


This time we would like to offer 20pcs of main shaft for FREE for the flyers from USA. Details as below :

1. "First come first serve"
2. 2pcs of shaft for EACH flyer. Limited for 10 flyers.
3. Shipping address must be within USA.
4. After you received the shaft. You have to post some words to let other people know what do you think about it. (positive or negative comments are welcome).

Anyone interested? :D
Please reply this thread to let us know.

[missle]

Count me in. What do you need from me to get a set?
Eric

[helitaiwan963]

Count me in too:D What do we need to do? maybe this should go to the Mini section?



Eric

[estarter]

Count me in also.

[Jeep_Angler]

I'm In :)

Greg

[mayday1]

count me in.

/tom

[Dogwoodtheone]

I'm game, count me in

[Speed Stick 3D]

I would Like some of these

Thanks

[spudandretti]

Me too.bud

[DriveWRX]

I'm in too!

[blade strike]

I'm game :cool:

I also crash hard :p

[FlyinLo]

I'd like to see if these are compatible with the Blade 400 I pre-ordered

[cre8or30]

count me in

[Gino CP]

Send some here in Manila. I am just as noisy around these forums.

[billyzelsnack]

I am sooo too late. Count me in. haha.

[mudder]

i'll take a set also! :D

[helitaiwan963]

where is this guy? posts this and no reply from him?

[HKAero-Nuts]

To the 14 flyers that above this message.
All of you could get 2pcs of shaft.

Would you please send me the shipping address through email?
Here is my Email : pan@aero-nuts.com

Please give me the following informations...

1.Your login name here
2.Your shipping address

Thanks all! :D

[Jeep_Angler]

Info sent...

Greg

[Gino CP]

Sadly an evaluation means we crash LOL.

[helitaiwan963]

mine is sent as well:D

[cmulder]

i am not a owner of a trex but am curious.
I asume you are starting a range of parts either cheaper then original or improved (hardened or other material)
Wil you start with other parts too?

[HKAero-Nuts]

>Wil you start with other parts too?
plastic tail rotor blade and 3D paddle is coming.

>either cheaper then original or improved (hardened or other material)
Our target is cheaper and better. :D
About this shaft : It was made by Stainless Steel and Precision finishing
It will be proved. :)

[DoctorAudio]

Darn it Count me in too! I need some free stuff!

Some company should come up with a cheap crash kit for the REX! That would be cool!

[Dogwoodtheone]

info sent

[FlyinLo]

e-mailed my information from dbarnes727(at)msn(dot)com

[HKAero-Nuts]

Jusy got the informations below...how is other people? :D

Gino CP
Jeep_Angler
Helitaiwan963
FlyinLo
DriveWRX
DogWoodtheone


To DoctorAudio
Thanks for your suggestion. please leave me your informations too. :D
At this moment we focus on making the high quality and preformance parts for CRAZY 3Der and the price is lower.

[FlyinLo]

HK, will you be making any dedicated Blade 400 parts when it comes out?

[Speed Stick 3D]

U should have my info also i sent an Email

Thanks Speed stick 3D

[DoctorAudio]

Email sent! Oh yeah! I love crazy 3D stuff!
That would include stuff like=
3D Paddles adjustable!
3D Blades adjustable lead-lag!
Light weight metal Servo arms!
Titanium control rods!
Titanium Flybar would be cool! It would just need to be lighter!
Cheap Carbon booms, that look as good as the Align ones. But like two in a pack for 10.00 bucks!
Titanium ball links too! I go thur like five sets a year. That would cut that down to like one a year!
Metal ball links with the ball all ready in them. Allyou have to do is screw them in! now that would be cool! reaplace the link and rod at same time! oh yeah!

That's my 2 cents worth!
Elvan Wilson II!

[missle]

Email sent with the info you requested. Thanks missle.

As I was checking out your website, I came accross your 2200 extreme 3S batteries so I was wondering if you wanted to include a couple of those for trial purposes also :D . Seriously though, let's work out something so I can try those out. Thanks Eric

[HKAero-Nuts]

The shaft is coming to your door. :D

And the Supreme Hobby Paddle and Tail blade is coming soon.
For more informations, please visit here

Tail Blade
http://www.aero-nuts.com/product_info.php?products_id=492
http://www.aero-nuts.com/images/450TailBlade.jpg

Paddle
http://www.aero-nuts.com/product_info.php?products_id=491
http://www.aero-nuts.com/images/450pabbles.jpg

[helitaiwan963]

i haven't gotten mine yet...

[HKAero-Nuts]

I mean coming soon. :D

I will offer some free paddle and tail blade for FREE also.
I will make the new thread when we got them.
Any 3D flyer want them?

[Jeep_Angler]

I mean coming soon. :D

I will offer some free paddle and tail blade for FREE also.
I will make the new thread when we got them.
Any 3D flyer want them?

I am in :) That would be great if you send some my way.

Greg

[DoctorAudio]

Since i fly both 3D helis and planes!
Send me any thing!

[DriveWRX]

I mean coming soon. :D

I will offer some free paddle and tail blade for FREE also.
I will make the new thread when we got them.
Any 3D flyer want them?

Interested in the paddles and blades too. Please count me in. Thanks! :D

[Jeep_Angler]

Got my main shafts today... I will be back on later with some comparison notes.

Thanks again!

Greg

[Jeep_Angler]

This is my initial comparison between the Supreme Hobby (SH) main shaft (provided by HKAero-Nuts) and an Align HS1011 main shaft, not installed on the heli.

The first thing I noticed when comparing the two side-by-side on the table is that the SH main shaft's machined collar ring is about 1mm lower down the main shaft than on the Align. The SH main shaft in general appears to be about a 1mm shorter in overall length as well. The depth of the machining for the collar on the SH main shaft also looks to run a little deeper than the Align shaft. I do not have a set of calipers or a mic to verify the exact difference between the two.

Next was the weight test. I measured the SH main shaft at exactly 17g. The Align weighed in at 17.3g.

After looking at both of the shafts in more detail, it appears that the Align shaft gets polished before machining and the SH shaft gets polished after machining. There is no evidence of a "sharp" transition edge between the machined surfaces and the main shaft surface on the SH shaft.

Pricing:

SH main shaft (part #SH450Shaft) price from website below $6.39 (3 pieces per bag)
http://www.aero-nuts.com/product_info.php?products_id=486

Align main shaft (part #HS1011-3) price $7.98 (3 pieces, 1 collar, 1 grub screw per bag)
http://www.helidirect.com/product_info.php?cPath=186&products_id=191

I was a little disappointed to see that the SH shafts don't even come with a collar on the website (so it appears that way). I didn't expect to get one with the two shafts given to me, but I would like to see the #SH450Shaft bag have a collar and a grub screw in it preferably a lower profile collar that would allow for more clearance between the swash plate and collar when at full negative collective and full cyclic.

Hopefully within the next week I can install the SH main shaft on my TREX and see if there is any noticeable differences between it and the Align shaft. I don't consider myself to be that good of a pilot to be able to tell the difference between a part such as a main shaft. So far, I see no reason not to put this shaft on my bird and give it a try. ;)

Greg

[helitaiwan963]

I got mine yesterday as well.I like the machining on these main shafts. The machining is very precise and clean. I like how they rounded off the edges and gives it a much better look.(even though u don't see it installed) but i like it sitting there:D I'll give them a try next time i need them which means crash:( But hey, we're all good at that arn't we??:D

[Speed Stick 3D]

Hi i got my shafts today.. they look really nice and i will be giving them to and danny szabo and my friend ben....Looks nice and they look alot better than the align ones.. ill be back with a post telling how they are after i get my friends to put some flight time on them..

Thanks Speed stick 3D :D

[helitaiwan963]

wow. i wanna see how these things hold up at like 3500 rpm headspeed. Get vids of danny flying them?

[DriveWRX]

Got mine in yesterday.
Quality is top notch! Great machining and finish.
Just need to get some flight time on these, which might be awhile do to the weather here...

[DoctorAudio]

Hello guys, I have been real busy with our new product too!

I recieved the new shafts in the mail a couple of days ago!
They look as others have said, real nice work! I will be putting them thur some test this weekend and I will be showing them off to a couple of our dealers this next week!
I checked them to see how true they are and spun them at 40,000 rpm, they are true!
The holes are in the right place and the shafts are the right lentgh too!

I don't know if you really need to put collars and grub screws in the bag. I have almost 20 or 30 collars and grub screws from all the one that I have bought in the past 4 years! Some may need them. But I have never lost either of these items in a crash.
But I will say if it is cost efective to put them in the package, then do so!

Anyway back to what feeds my house guys.
Keep them flipping and I will chat with all later!

Elvan Wilson
FlexPro Landing gear.
Regional Sales Manager
503-270-1695

[HKAero-Nuts]

Thanks for all of the comments above.
And our shaft is STAINLESS!! :D
It's very important for the people won't crash the heli.

To Greg
Thanks for your suggestion, We will make the collar later!

Anyone flying with 3500rpm headspeed? I wanna see the video with the 3D paddle too.
I got a pair of 3D paddle and tail blade now. :rolleyes:

Some more for free soon! :D

[Jeep_Angler]

To Greg
Thanks for your suggestion, We will make the collar later!

Anyone flying with 3500rpm headspeed? I wanna see the video with the 3D paddle too.
I got a pair of 3D paddle and tail blade now. :rolleyes:

Some more for free soon! :D

In regards to the collar, I think if you guys could produce a collar that is smaller (height and diameter) than the Align one that would be great. I notice that my current setup, the collar inferes a little with the swash plate during negative pitch and full cyclic.

I am up for the 3D paddle and tail blades as well :D

I hope to have a more detailed review on here over the holiday break as I have been swamped lately. I can't wait to give them a try.

Thanks,
Greg

[Speed Stick 3D]

Please send me some paddles and tail blades.. Ill put them through hell...and i bet they will be fine... I try to get a vid of alan jr flying them becuase danny is no longer with align...Thanks Also the collar would be ok also.. And you must have your swash settings set up wrong becuase when i had my T-Rex i was running almost 3850 rpms and getting 13-13 pitch with 8 degres of cyclic and doing hard 3D was no problem..

Thanks Speed stick 3D :D

T-Rex 450 Se V1
Align 430 Xl
4 Cell 2200 Thunderpower Extreme 25 C
CC 45 Hv
12 T pinion
Hs 65 Mg servos
Futaba 401/9650
Electron 6 reciver
Hitec eclipse 7

=

INSANE 3D

[HKAero-Nuts]

Jeep_Angler and Speed Stick 3D
I will ship my ONLY 2 pairs of tail blade and paddle to you tomorrow(it's the sample from factory). :D
Please let us know the difference after you flying with them.

3850rpm headspeed :eek: interesting!

[Jeep_Angler]

And you must have your swash settings set up wrong becuase when i had my T-Rex i was running almost 3850 rpms and getting 13-13 pitch with 8 degres of cyclic and doing hard 3D was no problem..



I should have made this more clear when talking about the collar interference... It was on my ESKY Honey Bee KingV2 with the TREX450 Head on it. My actual TREX450 has no interference.

Greg

[Jeep_Angler]

Jeep_Angler and Speed Stick 3D
I will ship my ONLY 2 pairs of tail blade and paddle to you tomorrow(it's the sample from factory). :D
Please let us know the difference after you flying with them.


Perfect! Thanks a bunch.

Greg

[Speed Stick 3D]

haaa yah sounds right..If it was made for it the head would be on it right... :) anyways Thanks and im looking forward to the paddles and tail blades


Thanks Speed stick 3D :D

[HKAero-Nuts]

Hey~ receive the sample tail blade and paddle? :D

[kahn1701]

Hello all.
Free stuff...
OK wheres the long lines? LOL
I would like to get on the list...I'll Test every thing you got.I'll post video on youtube.Also list info here.
I fly at lest 3 time a week. Or more.Please dont tell the wife..LOL