high torque servo

[TyBreaker]

Some time ago I was looking at Hi-tec HS-645MG servos for use in a
monster truck but as time as passed, I was wondering what folk are using
nowadays? I'm getting a TXT-1 and would like to get a steering servo
that can turn the wheels when moving slowly eg rock crawling.
--
______ ___ __
/_ __/_ __/ _ )_______ ___ _/ /_____ ____
/ / / // / _ / __/ -_) _ `/ '_/ -_) __/
/_/ \_, /____/_/ \__/\_,_/_/\_\\__/_/
/___/

There are 10 types of people in this world; those who understand the
binary numbering system and those who don't.

There's no place like 127.0.0.1.

ASCII a silly question, get a silly ANSI.

[DanTXD]

"TyBreaker" <tybreakerNO@SPAMhotmail.com> wrote in message
news:444a8df9@dnews.tpgi.com.au...
> Some time ago I was looking at Hi-tec HS-645MG servos for use in a monster
> truck but as time as passed, I was wondering what folk are using nowadays?
> I'm getting a TXT-1 and would like to get a steering servo that can turn
> the wheels when moving slowly eg rock crawling.


I have a Savage, 645 on steering here, 625 on throttle, no complaints :-)

--
Dan

[TyBreaker]

DanTXD wrote:
> I have a Savage, 645 on steering here, 625 on throttle, no complaints :-)

OK, I have a couple of other questions related to this. I notice you
can get digital vs analogue servos - what's the deal there? And also,
some servos are compatible with Hitec/JR radios and others with Futaba -
I haven't decided on a radio yet so is it possible to modify a servo
for a Hitec to fit a Futaba and vice versa? If it's a problem, I'll
just need to buy a radio earlier than I'd planned.

--
______ ___ __
/_ __/_ __/ _ )_______ ___ _/ /_____ ____
/ / / // / _ / __/ -_) _ `/ '_/ -_) __/
/_/ \_, /____/_/ \__/\_,_/_/\_\\__/_/
/___/

There are 10 types of people in this world; those who understand the
binary numbering system and those who don't.

There's no place like 127.0.0.1.

ASCII a silly question, get a silly ANSI.

[\Doc\]

"TyBreaker" <tybreakerNO@SPAMhotmail.com> wrote in message
news:444acd2f$1@dnews.tpgi.com.au...
> DanTXD wrote:
>> I have a Savage, 645 on steering here, 625 on throttle, no complaints :-)
>
> OK, I have a couple of other questions related to this. I notice you can
> get digital vs analogue servos - what's the deal there? And also, some
> servos are compatible with Hitec/JR radios and others with Futaba - I
> haven't decided on a radio yet so is it possible to modify a servo for a
> Hitec to fit a Futaba and vice versa? If it's a problem, I'll just need
> to buy a radio earlier than I'd planned.

I'm running Hitec 645MG's for steering on all three 1/8 scale vehix (Savage
Monster Truck, Mayhem ST Truggy and Kanai 3 Buggy) and Hobbico CS-64 on
throttle/brake. No complaints and they do their job well.

Futaba connectors have a little "fin" on one end of the connector that
prevents them from fitting into non-Futaba receivers. All you have to do is
cut that little fin off with a hobby knife or sand it off with a Dremmel and
they'll slide right in to non-Futaba rx'es.

Digital servos respond more quickly, center better and have more "stops"
between one end of servo travel and the other making precise adjustments
(sub-trim, trim) and more precise input movements possible. Very important
in airplanes and maybe touring cars and buggies, but they'd be a waste of
money in a TXT or any other MT for that matter.

Doc

[Richard]

"TyBreaker" <tybreakerNO@SPAMhotmail.com> wrote in message
news:444a8df9@dnews.tpgi.com.au...
> Some time ago I was looking at Hi-tec HS-645MG servos for use in a
> monster truck but as time as passed, I was wondering what folk are using
> nowadays? I'm getting a TXT-1 and would like to get a steering servo
> that can turn the wheels when moving slowly eg rock crawling.


I bought 4 cheap Tower Pro copies of the Hitec servos off ebay. Paid $30
(AUS) each for them. They are rated at 15Kg/cm (6v) and have dual ball
bearings. Replacement parts as I have been told come from Hitec 945MG's,
but at $30 I can afford to break a servo and replace as needed.

I have one at each end of my Clod and one in each of my nitro trucks. I've
actually found them to be too fast for steering on the nitro trucks and with
no servo saver in my Clod I have yet to break a gear.

http://www.rcuniverse.com/market/item.cfm?itemId=183997
Ebay item number 6052134705 if your interested


Cheers
Richard

[TyBreaker]

"Doc" wrote:
> Futaba connectors have a little "fin" on one end of the connector that
> prevents them from fitting into non-Futaba receivers. All you have to do is
> cut that little fin off with a hobby knife or sand it off with a Dremmel and
> they'll slide right in to non-Futaba rx'es.

Does this fin removal still result in a snug fit or is it loose? Also,
sounds like the reverse may be a problem then ie fitting a non-Futaba
servo to a Futaba receiver? I guess even if it's a tad loose, one could
always engineer something to hold it in place?

> Digital servos respond more quickly, center better and have more "stops"
> between one end of servo travel and the other making precise adjustments
> (sub-trim, trim) and more precise input movements possible. Very important
> in airplanes and maybe touring cars and buggies, but they'd be a waste of
> money in a TXT or any other MT for that matter.

Thanks for this info - I've found it a real struggle to find basic rc
info like this anywhere on the web.

I'm very happy with ebay though - such savings on the kit, ball bearings
etc, much better than my local LHS. Where I live there are only two and
both have healthy profit margins ;)

--
______ ___ __
/_ __/_ __/ _ )_______ ___ _/ /_____ ____
/ / / // / _ / __/ -_) _ `/ '_/ -_) __/
/_/ \_, /____/_/ \__/\_,_/_/\_\\__/_/
/___/

There are 10 types of people in this world; those who understand the
binary numbering system and those who don't.

There's no place like 127.0.0.1.

ASCII a silly question, get a silly ANSI.

[M78Ultra]

Hey cool,
Glad to hear someone is using those (mg995) and they hold up well...I just
ordered 3 of them a few days ago just to try them.
$12 + shipping... figured worth a shot since the specs looked decent.
ebay item: 6051391282

"Richard" <DK@hotmail.com> wrote in message
news:444b17f2@quokka.wn.com.au...
>
> "TyBreaker" <tybreakerNO@SPAMhotmail.com> wrote in message
> news:444a8df9@dnews.tpgi.com.au...
> > Some time ago I was looking at Hi-tec HS-645MG servos for use in a
> > monster truck but as time as passed, I was wondering what folk are using
> > nowadays? I'm getting a TXT-1 and would like to get a steering servo
> > that can turn the wheels when moving slowly eg rock crawling.
>
>
> I bought 4 cheap Tower Pro copies of the Hitec servos off ebay. Paid $30
> (AUS) each for them. They are rated at 15Kg/cm (6v) and have dual ball
> bearings. Replacement parts as I have been told come from Hitec 945MG's,
> but at $30 I can afford to break a servo and replace as needed.
>
> I have one at each end of my Clod and one in each of my nitro trucks. I've
> actually found them to be too fast for steering on the nitro trucks and
with
> no servo saver in my Clod I have yet to break a gear.
>
> http://www.rcuniverse.com/market/item.cfm?itemId=183997
> Ebay item number 6052134705 if your interested
>
>
> Cheers
> Richard
>
>