JR and Futaba trainer cables

[Fonz]

Can anyone help me with a link for trainer cables for my JR-378.
I know thatJR to JR is just a straight through 3.5mm mono plug, but I would
also like to have:
JR to Futaba
JR to DSC (direct servo connect) to receiver.
Many thanks in advance.
Rob F.
Melbourne Australia.

[The OTHER Kevin in San Diego]

On Wed, 12 Apr 2006 15:21:32 +1000, "Fonz" <r@removeme.com.au> wrote:

>Can anyone help me with a link for trainer cables for my JR-378.
>I know thatJR to JR is just a straight through 3.5mm mono plug, but I would
>also like to have:
>JR to Futaba
>JR to DSC (direct servo connect) to receiver.
>Many thanks in advance.
>Rob F.
>Melbourne Australia.

OK, I'm betting within 12 hours of this posting, Alan's Hobbies will
post their usual "Hey, come look at all these links" response :)

[Beav]

"Fonz" <r@removeme.com.au> wrote in message
news:443c8e5e@dnews.tpgi.com.au...
> Can anyone help me with a link for trainer cables for my JR-378.
> I know thatJR to JR is just a straight through 3.5mm mono plug, but I
> would also like to have:
> JR to Futaba

Won't happen. Different systems and they're not compatible.

> JR to DSC (direct servo connect) to receiver.

Entirely possible as they're in the JR range. 3.5jack to Rx plug.



--
Beav
OMF#19
VN 750
Zed Thou

mail is beavis dot original at ntlworld dot com (with the obvious changes)

[Fonz]

Found the link I was looking for. This one says it is possible.
www.uoguelph.ca/~antoon/gadgets/futjr.html
I'm going to send him an email and see if he has actually used it.
Rob.

"Beav" <beavis.original@ntlwoxoorld.com> wrote in message
news:Udf%f.46573$Nh7.20061@newsfe4-win.ntli.net...
>
> "Fonz" <r@removeme.com.au> wrote in message
> news:443c8e5e@dnews.tpgi.com.au...
>> Can anyone help me with a link for trainer cables for my JR-378.
>> I know thatJR to JR is just a straight through 3.5mm mono plug, but I
>> would also like to have:
>> JR to Futaba
>
> Won't happen. Different systems and they're not compatible.
>
>> JR to DSC (direct servo connect) to receiver.
>
> Entirely possible as they're in the JR range. 3.5jack to Rx plug.
>
>
>
> --
> Beav
> OMF#19
> VN 750
> Zed Thou
>
> mail is beavis dot original at ntlworld dot com (with the obvious changes)
>

[Tom Minger]

I am currently instructing a guy who bnought the Horizon Hobbies P-51
"trainer" set up. The set came with a buddy box cord, but not a buddy box
xmtr. This P-51 trainer outfit comes with JR equipment installed, including
a low end JR xmtr (can't remember which model no.). The provided buddy box
cord on one end has just a JR plug, and on the other end is split with both
the JR plug and a Futaba 5-pin DIN connector. This cord must be available
separately from Horizon.

Someone else needs to chime in about the JR DSC; I'm a Futaba guy.

"Fonz" <r@removeme.com.au> wrote in message
news:443c8e5e@dnews.tpgi.com.au...
> Can anyone help me with a link for trainer cables for my JR-378.
> I know thatJR to JR is just a straight through 3.5mm mono plug, but I
> would also like to have:
> JR to Futaba
> JR to DSC (direct servo connect) to receiver.
> Many thanks in advance.
> Rob F.
> Melbourne Australia.
>
>