Gws 22xx 系列無刷馬達即將上市

[GWS4CEO]

GWS 22XX 系列無刷馬達即將上市. :)
http://www.gws.com.tw/chinese/product/auxcircuit/brushless.htm

http://www.gws.com.tw/chinese/product/motor/006.htm

http://www.gws.com.tw/images/product/gwblm001.jpg

請密切注意． :cool:

[GWS4CEO]

測試數據如下:

[GWS4CEO]

測試方法與過程. :)

[GWS4CEO]

第一批馬達與15a電變esc已經由大陸出貨向台灣及美國去. :cool:

相信年初大家就可以窺豹一斑. :)

[Kai@UCSB]

終於終於 :D
恭喜
不過便宜的變電需求更大

-Kai

[GWS4CEO]

終於終於 :D
恭喜
不過便宜的變電需求更大

-KaiGWS ESC15A 美國賣價$25.00 夠得上便宜嗎? :rolleyes:

GWS 2205 BL motor 美國賣價$15.00 夠得上便宜嗎? :D

[GWS4CEO]

注意事項: Be sure to follow the notes as below:

1. KV值2050
Its KV value is 2050.

2. 馬達極限為90W請勿高速持續使用5分鐘..超過140W請勿超過10秒鐘
Never let it run continually for over than 5 minutes when its power reaches 90W. Nerver let it run continually for over than 10 seconds when its power reaches 140W.

3. 使用在3D飛機其全備重量應在350克以下
It is recommended to use this motor on 3D airplane with its total flying weight less than 350g (12.36 oz).

4. 馬達使用中請保留馬達散熱孔以幫助散熱
It is required to keep good ventilation for this motor during its running hours.

5. 馬達溫度請勿超過70度C.
This motor could not work when its temperature goes higher than 70 degrees Centigrade (158 degrees Fahrenheit).

6. 90W時溫度會立即超過40度C並快速升高.
Its temperature would goes higer than 40 degrees Centigrade (104 degrees Fahrenheit) very quickly when its power reaches 90W.

7. 螺旋槳建議不要超過 8043 ( 8x4.3吋 ) 的尺寸並以使用2S LiPo 7.4V電池為宜.
Using propeller size longer than 8043(8”x4.3”) on this motor is not recommended, but using a 2S LiPo 7.4V battery pack with this motor is highly recommended..

8. 電壓在7.4v 時馬達電流不要超過12A
It is not allowed to reach current drawing for over than 12A when voltage 7.4V (2S LiPo) is applied on this motor.

9. 電壓在11.1v時馬達電流不要超過8A
It is not allowed to reach current drawing for over than 8A when voltage 11.1V (3S LiPo) is applied on this motor.

[blackdogroad]

GWS4CEO:

Good job. I just ordered a couple of your motors/15amp speed controls from AllERC. I'm very excited for the package to arrive. Is it too good to be true? I have been building CD Rom motors for a while, but yours comes with all the hardware (mounting, bullet connectors) for $15? ALLERc has a combo deal which works out to $36 for the motor AND speed control. I think its going to be a good value.

Do you have other winds coming soon? I'm already dreaming of rewinding the motor and I haven't even got it in my hands yet! :) I have a home made blucore foam B25 with twin CDR motors, and I might just try these with it.

If you are a publicly traded company, I want to invest!

Thanks much.

df

[GWS4CEO]

After the best performance on the production and hand over motors to you, we will continiously keep trying more different choice of winds. ;)

However, we like to hear more about your opinions...

[GWS4CEO]

Recntly, I saw a Taiwan's flyer modified his GWS Spitfire with fibre covering all the surface, repainted weight up to 800g. :)

Powered by a brushless motor 200W by EPS400C gear drive, with ??8085 prop gave 700g thrust. ;)

Flying very fast likes JET. :eek:

However, GWS BL motors is comming! :)

I believe GWS 2208 can fly GWS WW-IIs with great performance. :cool:

GWS 2212 may drive our WW-II fast like roket! But need to beware of wing be bent and cause crash! :D

[GWS4CEO]

The price of GWS BL motors in USA:

2205 $15.
2208 $18.
2212 $21.

[yctseng]

GWS4CEO 林董, 1300KV, 用 EP-7035 7.4V 工作會有 11500rpm ?
7.4*1300= 9620, 貴公司的東西會有超能力 ?

[GWS4CEO]

KV值重測後修正為 2050. :p

http://www.gws.com.tw/chinese/product/motor/006.htm

[GWS4CEO]

http://www.gws.com.tw/chinese/product/auxcircuit/brushless.htm

OUTRUNNERS Brushless Motor 2205/15T 建議售價/ NT$430; MSRP in USA $15.

OUTRUNNERS Brushless Motor 2208/18T 建議售價/ NT$515; MSRP in USA $18.

OUTRUNNERS Brushless Motor 2212 建議售價/ NT$600; MSRP in USA $21.

Brushless ESC 無刷電子變速器 GWESC15A 建議售價/ NT$715; MSRP in USA $25.

Brushless ESC 無刷電子變速器 GWESC25A 建議售價/ NT$1000; MSRP in USA $35.

Brushless ESC 無刷電子變速器 GWESC35A 建議售價/ NT$1300; MSRP in USA $45.

[GWS4CEO]

Since the great cost-performance, 1st batch GWS BL motors and BL ESCs were all gone in short time. :)

Tonight GWS China QC staffs and production line will overtime till the last batch of BL motors and BL ESCs to be finished for tomorrow's shipment before Chinese New Year vocation started. ;)

I am not sure when will they able to finish, but its time for me to go bed, I need to wake up early again as every morning. :)

[unochen]

http://www.gws.com.tw/chinese/product/auxcircuit/brushless.htm

OUTRUNNERS Brushless Motor 2205/15T 建議售價/ NT$430; MSRP in USA $15.

OUTRUNNERS Brushless Motor 2208/18T 建議售價/ NT$515; MSRP in USA $18.

OUTRUNNERS Brushless Motor 2212 建議售價/ NT$600; MSRP in USA $21.

Brushless ESC 無刷電子變速器 GWESC15A 建議售價/ NT$715; MSRP in USA $25.

Brushless ESC 無刷電子變速器 GWESC25A 建議售價/ NT$1000; MSRP in USA $35.

Brushless ESC 無刷電子變速器 GWESC35A 建議售價/ NT$1300; MSRP in USA $45.

很便宜耶
:D :D :D

[RAY GWS]

Hi Unochen,

How are you doing?

The price is reasonable and it will benefit many flyers around the world.

We do have huge demand for this.

Dealers need to place order early and wait in line.


Ray

[GWS4CEO]

Finally, GWS China staffs finished the motors and ESCs on time to be shipped on the way to many countries... :)

[unochen]

Hi Unochen,

How are you doing?

The price is reasonable and it will benefit many flyers around the world.

We do have huge demand for this.

Dealers need to place order early and wait in line.


Ray

RAY
好久不見，
自從飛過福爾摩沙二代後，需要一點挑戰，所以現在改飛直昇機了，電直機齡3個月、油直2個月，
要不是福爾摩沙太好飛，我可能還繼續飛電機吧！
它的動作準又無無癖性，飛起來根本沒什麼壓力，是一台好飛機，
我現在改換一下跑道，嘗試不一樣的飛行器。
你們公司最近推出無刷馬達及無刷電子變速器價格實在太吸引人，
性能一定是頂棒的，相信會再掀起世界另一波的飛行熱潮。

:D :D :D

[GWS4CEO]

GWS China just finished 2nd batch of BL motors and ESC. Catch on time to tranship out from Hong Kong via TNT, UPS and Fedex before Chinese New Year Vocation started. :)

[RAY GWS]

RAY
好久不見，
自從飛過福爾摩沙二代後，需要一點挑戰，所以現在改飛直昇機了，電直機齡3個月、油直2個月，
要不是福爾摩沙太好飛，我可能還繼續飛電機吧！
它的動作準又無無癖性，飛起來根本沒什麼壓力，是一台好飛機，
我現在改換一下跑道，嘗試不一樣的飛行器。
你們公司最近推出無刷馬達及無刷電子變速器價格實在太吸引人，
性能一定是頂棒的，相信會再掀起世界另一波的飛行熱潮。

:D :D :D
GWS CEO will create a special version of brushless motor.

Wait and see. It is a motor with innovation and creative idea. Many flyers will love it.

Ray

[blackdogroad]

Hi GWS-CEO

I can say the GWS 15T motors are super. I built a from-scratch foam/carbon P38 and mounted two of the 15T with 7x3.5 GWS props. Ever see a p-38 hover? At these prices, it is AOK to use these kind of brushless motors in pair and even quads!

Only one issue: The shaft/prop flew out of my motors. How crazy. After about 5 flights, I went to hand launch. Advance the throttle and the prop flew right out. I found the set screw was very loose and allowed the shaft to slip through. I put lock-tight and reset the shaft. Then, upon inspection of the other motor, its setscrew was not tight at all. I put lock-tight there as well.

I have ordered 4 more from All-e-rc. But, unfortunately, we are they are out of stock and I'm awaiting my shipment. I'm torn about trying to scratch build a 4 motor type plane, or several single /doubles.

Keep the factories at full production! :)

[GWS CHEN]

Hi

It's great to know you have built a P38 powered by two 2205/15T. Oh I would need
to keep my colleague informed of the problem of screw setting.

The 2nd lot of GWS 2205/15 has been shipped out since Jan. 27, 2006, hope you
could receive your 4 new motors soon.

Could you post some photos of your P-38. I'd believe that they are great, too.

[blackdogroad]

Hi Everyone...

Here is the P-38. I used 3/4 blue foam, blucor elevator and wing. On the wing, I took a different approach: I laminated a strip of 2" wide foam to the top, leading edge of the wing. And, add to that a 1/8" carbon fiber rod, its rock solid!

I built "box" type motor mounts out of 1/16" ply. Very solid and light weight for this application.

Very stable plane. It will take off from hand launch vertically and hang there. I have no rudders, so I need to make it dance via aileron/elevator inputs. After a few seconds, it breaks to the left and away we go! Recovery is no problem. All in all, these motors give it life. I would trade some thrust for some speed, though. A variety of winds in this size motor would be super.

Also, got word 4 more of my GWS motors were shipped by all-e-rc today! This means by the weekend (hopefully) I'll be able to build a few more. I'm going to design a p-40 warhawk using this same construction. Maybe a p-51 and a b25.


df

[GWS CHEN]

Hi blackdogroad

Thank you for your sound photos.

Would you post the same story of your P-38 and new warbirds on another English thread. More flyers on R/C Group would like to
know the new usage of GWS2205/15.

[blackdogroad]

Hi,

Yep, will post in rcgroups. I've gotten 4 more motor/esc combos, and built a p40, me109, j3 cub and working with the neighborhood kids teaching them how tobuild. We are building a thunderbolt, all from sratch. The motors are quite fine. I really like that you have a super hardware pack.

Thanks. AND, we need the 2208 soon!

[GWS4CEO]

Just start to test more proto type samples of GWS 2212 motors.

Now, we are testing 14T, 15T, 16T and 17T.

GWS 2212 will be keep tested with more different windings and props to be run under 2, 3 and 4 cells.

I believe that we will make great effert on this motor to let her run with excellent performance.

Yet, I am working on 2215 proto type. We like to let 2215 get more than 1000g thrust easily!

Hope GWS 2215/XX will be able to give more thrust than AXI 2212s. But priced for $24.

[GWS4CEO]

Prop V Amp Thrust/g RPM

2215-10T kv~1040
EP1147 10.7V 20.02A 1000g 6160
EP1047 10.8V 17.55A 900g 6950

2215-11T kv~945
EP1147 10.7V 17.26A 960g 6000
EP1047 10.8V 14.73A 900g 6650

2215-12T kv~874
EP1147 10.8V 14.2A 840g 5700
EP1047 10.8V 12.4A 800g 6360

[GWS4CEO]

7.40V 6.00A 330g 5100RPM 44.40W 7.43g/W
11.1V 10.7A 628g 6900RPM 118.77W 5.29g/W
14.8V 15.9A 980g 8500RPM 235.32W 4.16g/W

Hope this will help 3D flyers very happy! ;)

Even Formosa-II can use 2215 for practice! :)

[GWS4CEO]

GWS 2212 and 2208 BL motors had shipped out from GWS China a few days ago. Should be at the store soon. :)

2215 will be run on the production line on about 30~40 days later. ;)

[GWS CHEN]

請向廣營昆陽門市或各模型店洽購2208/18,2212/13及ESC25A.

Would you contact GWS Kun Yang shop or another hobby shops
for buying 2208/18, 2212/13 and ESC25A.

[GWS CHEN]

Spare shaft of GWS2205/15 is available currently.
New mount for brshless motors will be available before the end
of May. There have been some pieces available in GWS KunYang
shop.

Post #205 of this link http://www.rcgroups.com/forums/showthread.php?t=358516&page=14&pp=15

廣營無刷馬達220515的備用轉軸已經上市.
廣營無刷馬達專用馬達座五月底之前上市. 昆陽門市現在已有少數庫存.