where to buy Raptor?

[sbc]

Where is the best place to buy a Raptor 90? I recall I vendor in China that
had good pricing but can't remember the name.

[www.HeliRaptor.com]

Not sure where you are from but here are 2 sites that I like:

www.onlyraptors.com
www.heliproz.com

I have shopped at both and never had any issues. Prices are pretty
good also.

Hope this helps.

Dennis

[kodi946]

Must be thinking of cyberheli in Hong Kong. I spoke with the owner (can't
remember the name) 2 years ago when I got my Raptor 30. Nice guy very
helpful and great prices but shipping was too much to the States so I went
with Heliproz. At the time Heliproz prices were a little higher but they
are also VERY helpful and anyone who answers the phone is a heli pilot. I
highly recommend them. Helped me setup my 401 when Futaba couldn't answer
my questions.


"sbc" <rossvjohnson@sbcglobal.net> wrote in message
news:eeQde.12320$J12.9170@newssvr14.news.prodigy.c om...
> Where is the best place to buy a Raptor 90? I recall I vendor in China
that
> had good pricing but can't remember the name.
>
>

[gary]

does anyone have an opinion about this raptor 30 at heliproz?
http://www4.mailordercentral.com/heliproz/prodinfo.asp?number=RAPTOR37SKU

i'm thinking about stepping up from electric.
gary




"kodi946" <kodi946@adelphia.net> wrote in message
news:yZCdneo2gcEVU-HfRVn-2g@adelphia.com...
> Must be thinking of cyberheli in Hong Kong. I spoke with the owner (can't
> remember the name) 2 years ago when I got my Raptor 30. Nice guy very
> helpful and great prices but shipping was too much to the States so I went
> with Heliproz. At the time Heliproz prices were a little higher but they
> are also VERY helpful and anyone who answers the phone is a heli pilot. I
> highly recommend them. Helped me setup my 401 when Futaba couldn't answer
> my questions.
>
>
> "sbc" <rossvjohnson@sbcglobal.net> wrote in message
> news:eeQde.12320$J12.9170@newssvr14.news.prodigy.c om...
>> Where is the best place to buy a Raptor 90? I recall I vendor in China
> that
>> had good pricing but can't remember the name.
>>
>>
>
>

[kodi946]

Looks good to me. My Raptor 30 V2 only has the os32 and flys well but I'm
not doing 3d. From what I have been reading on the net if you want to get
into 3d go for the Raptor 50. Same as 30 with bigger motor, blades and
boom. The 50 will take you further up the learning curve. If you're not
into 3d then the 30 listed below will be a nice flying heli. Ok for
aerobatics but not the heavy 3d stuff.


"gary" <gls@nospam.net> wrote in message
news:Myife.2461$eU.1340@fed1read07...
> does anyone have an opinion about this raptor 30 at heliproz?
> http://www4.mailordercentral.com/heliproz/prodinfo.asp?number=RAPTOR37SKU
>
> i'm thinking about stepping up from electric.
> gary
>
>
>
>
> "kodi946" <kodi946@adelphia.net> wrote in message
> news:yZCdneo2gcEVU-HfRVn-2g@adelphia.com...
> > Must be thinking of cyberheli in Hong Kong. I spoke with the owner
(can't
> > remember the name) 2 years ago when I got my Raptor 30. Nice guy very
> > helpful and great prices but shipping was too much to the States so I
went
> > with Heliproz. At the time Heliproz prices were a little higher but
they
> > are also VERY helpful and anyone who answers the phone is a heli pilot.
I
> > highly recommend them. Helped me setup my 401 when Futaba couldn't
answer
> > my questions.
> >
> >
> > "sbc" <rossvjohnson@sbcglobal.net> wrote in message
> > news:eeQde.12320$J12.9170@newssvr14.news.prodigy.c om...
> >> Where is the best place to buy a Raptor 90? I recall I vendor in China
> > that
> >> had good pricing but can't remember the name.
> >>
> >>
> >
> >
>
>