JR and Hitec 945 Servo

[Wind and Snow]

Hi,

Is there any problem with using a JR XS3 radio and reciever with Hitec
servos? I have hitec a 945 steering and 925 throttle servo and need a
radio/reciever. i was going to buy a JR XS3 and plug those servos in. want
to make sure i am not going to break anything? sorry if this is a dumb
question. i am a little new to this.

Thanks for the help.

Cheers

Paul

[Justin Mahn]

I have a R300 receiver and it works fine with my Hitec 945 servo.

--
Justin Mahn
remove Panties to e-mail


"Wind and Snow" <paul.c@snet.net> wrote in message
news:k%k4d.22568$ZC7.20569@newssvr19.news.prodigy. com...
> Hi,
>
> Is there any problem with using a JR XS3 radio and reciever with Hitec
> servos? I have hitec a 945 steering and 925 throttle servo and need a
> radio/reciever. i was going to buy a JR XS3 and plug those servos in.
> want
> to make sure i am not going to break anything? sorry if this is a dumb
> question. i am a little new to this.
>
> Thanks for the help.
>
> Cheers
>
> Paul
>
>

[Wind and Snow]

Thanks Justin. Just wanted to be sure.

Regards,

Paul

"Justin Mahn" <gabrilPanties@tcainternet.com> wrote in message
news:10l3r04tj48rj25@corp.supernews.com...
> I have a R300 receiver and it works fine with my Hitec 945 servo.
>
> --
> Justin Mahn
> remove Panties to e-mail
>
>
> "Wind and Snow" <paul.c@snet.net> wrote in message
> news:k%k4d.22568$ZC7.20569@newssvr19.news.prodigy. com...
> > Hi,
> >
> > Is there any problem with using a JR XS3 radio and reciever with Hitec
> > servos? I have hitec a 945 steering and 925 throttle servo and need a
> > radio/reciever. i was going to buy a JR XS3 and plug those servos in.
> > want
> > to make sure i am not going to break anything? sorry if this is a dumb
> > question. i am a little new to this.
> >
> > Thanks for the help.
> >
> > Cheers
> >
> > Paul
> >
> >
>
>

[Justin Mahn]

just make sure the negative wire (brown or black in most cases) is to the
outside of the receiver. depending on the connector you get you may have to
trim the futaba key off or bevel the corners to get a good fit.

--
Justin Mahn
remove Panties to e-mail


"Wind and Snow" <paul.c@snet.net> wrote in message
news:oTy4d.7714$Qv5.6933@newssvr33.news.prodigy.co m...
> Thanks Justin. Just wanted to be sure.
>
> Regards,
>
> Paul
>
> "Justin Mahn" <gabrilPanties@tcainternet.com> wrote in message
> news:10l3r04tj48rj25@corp.supernews.com...
>> I have a R300 receiver and it works fine with my Hitec 945 servo.
>>
>> --
>> Justin Mahn
>> remove Panties to e-mail
>>
>>
>> "Wind and Snow" <paul.c@snet.net> wrote in message
>> news:k%k4d.22568$ZC7.20569@newssvr19.news.prodigy. com...
>> > Hi,
>> >
>> > Is there any problem with using a JR XS3 radio and reciever with Hitec
>> > servos? I have hitec a 945 steering and 925 throttle servo and need a
>> > radio/reciever. i was going to buy a JR XS3 and plug those servos in.
>> > want
>> > to make sure i am not going to break anything? sorry if this is a dumb
>> > question. i am a little new to this.
>> >
>> > Thanks for the help.
>> >
>> > Cheers
>> >
>> > Paul
>> >
>> >
>>
>>
>
>