Supervee won't start,please helpp

[ecanate]

Hi you doing guys,I got a little problem with my supervee brusless,I got it off ebay,the seller said that the speed control stoped working but everything else was in perfect condition,I know i shouldn't get staff from ebay,they tend not to work.but anyways I got a new speed contro last week,and nothing happens,batteries are fully charged, the electronics works because the RUDDER BLADE move side to side and when I turn the radio on, the boat starts bepping but when pull the trigger stops bepping and nothing happens,I thougt It was the speed control but I don't know now. I even fill up my tub with water and put it inside to see if only works on water and guess what..nothing happed. today I bouth a new motor it will be here in a week,until then please tell me what you think and thanxs for you time.

[seadog985]

try adjusting the throttle knob on the radio, it might be turned all the way down. i'm guessing channel 2 on your rx is good if the esc/motor beep when you plug it in. oh, i wouldn't put an sv27 in a tub and pull the trigger, something is going to get broken :eek:

[toesup]

... when I turn the radio on, the boat starts bepping but when pull the trigger stops bepping and nothing happens...

Sounds like the ESC needs programming...

[CG Bob]

Every time you plug charged batteries into the Aquacraft SV27 esc, you need to progam the esc. Direct from the SV27 BL manual (http://manuals.hobbico.com/aqu/aqub17-manual.pdf) is the proper procedure:
1. Turn the power "ON" to the transmitter.
2. Plug the batteries into the speed control plugs and listen for a single BEEP.
3. Pull the throttle trigger to full throttle and hold until you hear one BEEP.
4. Release the triggerand you will hear 5 more evenly spaced short BEEPS.
The motor is now armed and ready for operation.

[Rex R]

if when you a) turn on the tx and then b)plug in the boat batteries, the boat starts beeping... that indicates that the tx throttle trim is incorrectly set. you'll need to start turning the trim down untill the boat stops beeping. then give it full throttle(one beep) and release(four beeps) the next pull on the throttle should make the motor spin :)
rex

[ecanate]

hey guys thaxs so much for your help and you time, I connected the batteries and started bipping then I turn on the radio and started playing with the small knobs,turn the switches up and down also the trigger I pressed back and forwer and walla started working I disconnected again yust in case, and it worked,It fells good for now tomorrow I'm going to take for a spin at Central Park they have special lake for that.now I also have a Nitro supervee that I have to take apart because the string you pull to started It got stock and I can't pull it anymore,now my question is how do you turn it off once it gets started I started once and it was so frikking loud I didn't know how to stop it so I pull the tube connected to the small gas tank,I friking burn my fingers but whatever HOW DO YOU STOP A RUNNING NITRO BOAT??from the radio???thaxs

[ecanate]

thaxs for the responces I really apreciate.

[ecanate]

thank you, I never got the brushless manual I though I was yust connect and go,but thanxs I'll be glad to answer some of your trouble if I know the answer.later

[rcphreak]

one way to stop a running nitro boat is to pinch the fule line going into the carborator .
that is the best way to do it if in an emergency situation you can plug the exaust .
now that i have said that you need to . get used to driving a nitro boat and rember there is NO reverse . you can set up your throttle that when you push forward on the trigger ( as if it had reverse ) it kills the motor you have to set your idle screw so that it will let you do this . it will take some getting used to but is much safer than any other method .
also you need to install afail safe in the boat so that incase of dead batteries or siginal loss . it will automaticly shut down the boat so it does not run away / destroy its self or any one in the process . thanks
wayne