harvest
Jul 01, 2009, 12:23 AM
The most competitive prices
Below is a brief introduction of our digital servos. You can find more in the attached document and on our website: http://www.geningrc.com
GN Digital Servo Features:
It is high performance micro digital servo and is specially designed for 3D airplanes and helicopters, and glider application.
GN High-Speed Digital Servo provides extremely accurate neutral position. These servos are tailored for
3D fixed wing planes and micro electric helicopters. These digital servos can also find their position in the field of industrial automation which needs accurate and high speed control.
High fidelity MCU and excellent algorithm make it works smoothly and keep high frequency noise minimized.
GN Digital Servos adopt Frequency Conversion Technology enabling cool running temps under wild and long time 3D flight! This also provides for lower power consumption and this advanced technology guarantees the durability of GN Digital Servo.
GN D90 Micro Digital Servo（as tail servo）
Specs:
Operating Voltage: 4.8-6.0 Volts
Operating Speed (4.8V): 0.08sec/60°
Operating Speed (6.0V): 0.07sec/60°
Stall Torque (4.8V): 1.8kg.cm
Stall Torque (6.0V): 2.0kg.cm
Dead Band Width: ≤3usec
Current Drain (4.8V): 5.0mA/idle and 130mA no load operating
Current Drain (6.0V): 6.0mA/idle and 140mA no load operating
Dimensions: 0.92" x 0.45"x 0.86" (23.6 x 11.6 x 22mm)
Weight: 9.8g
Bearing Type: Top Ball Bearing
Gear Type: Carbon-nylon Gears
Motor Type: 3-Pole Neodynium Magnet
Connector Wire Length: 170mm
Operating Angle: 40 Deg. one side pulse traveling 400usec
Operating Temperature Range: -20 to +60 Degree C
Features:
• High speed and sensitivity
• Accurate,centers well
• Full AVCS Gyro DS mode compliant
• Strong,smooth
• Fall safe feature (Lost Signal Protection) --- The Digital Servo holds its position and torque during occasional signal lost.
• Light weight but perdurable structure will not interfere the 3D maneuverability of your plane.
GN D90MG Micro Digital Servo(as tail servo)
Specs:
Operating Voltage: 4.8-6.0 Volts
Operating Speed (4.8V): 0.08sec/60°
Operating Speed (6.0V): 0.07sec/60°
Stall Torque (4.8V): 1.8kg.cm
Stall Torque (6.0V): 2.0kg.cm
Dead Band Width: ≤3usec
Current Drain (4.8V): 5.3mA/idle and 140mA no load operating
Current Drain (6.0V): 6.6mA/idle and 150mA no load operating
Dimensions: 0.92" x 0.45"x 0.86" (23.6 x 11.6 x 22mm)
Weight: 13g
Bearing Type: Top Ball Bearing
Gear Type: Metal Gears
Motor Type: 3-Pole Neodynium Magnet
Connector Wire Length: 170mm
Operating Angle: 40 Deg. one side pulse traveling 400usec
Operating Temperature Range: -20 to +60 Degree C
Features:
• High speed and sensitivity
• Accurate,centers well
• Full AVCS Gyro DS mode compliant
• Strong,Smooth
• Metallic Copper Gears
• Fall safe feature (Lost Signal Protection) --- The Digital Servo holds its position and torque during occasional signal lost.
• Light weight but perdurable structure will not interfere the 3D maneuverability of your plane.
GN D95 and D95MG Micro Digital Servo
Specs:
Operating Voltage: 4.8-6.0 Volts
Operating Speed (4.8V): 0.09sec/60°
Operating Speed (6.0V): 0.08sec/60°
Stall Torque (4.8V): 2.0kg.cm
Stall Torque (6.0V): 2.2kg.cm
Dead Band Width: ≤3usec
Current Drain (4.8V): 5.3mA/idle and 140mA no load operating
Current Drain (6.0V): 6.6mA/idle and 150mA no load operating
Dimensions: 0.92" x 0.45"x 0.86" (23.6 x 11.6 x 22mm)
Weight: 13g
Bearing Type: Top Ball Bearing
Gear Type: Metal Gears
Motor Type: 3-Pole Neodynium Magnet
Connector Wire Length: 170mm
Operating Angle: 45 Deg. one side pulse traveling 400usec
Operating Temperature Range: -20 to +60 Degree C
Features:
• Quick,strong,smooth
• Accurate,centers well
• Metallic Copper Gears
• Full AVCS Gyro DS mode compliant and all receiver
• Top Ball Bearing
• Fall safe feature (Lost Signal Protection) --- The Digital Servo holds its position and torque during occasional signal lost.
• Light weight but perdurable structure will not interfere the 3D maneuverability of your plane.
D39BB Nano Digital Servo (Equipped with two ball bearings)
SPEC:
working voltage range: 4.0V-6.2V
Dynamic Torque: 0.5kg.cm @4.8V
Static Torque: 0.8kg.cm @4.8V
Speed: 0.08sec/60degrees@4.8V
Dead Band Width: ≤3us
Current Draw: Idle:0.10A; Running:0.30A; Stall:0.40A@5.0V
Servo Lead Gauge: 30#
Micro Coreless motor
Dimensions 19x17.5x8mm
Weight: 3.9g
D45BB Nano Digital Servo (Equipped with two ball bearings)
SPEC:
working voltage range: 4.0V-6.2V
Dynamic Torque: 0.6kg.cm (8.4 oz.in)@4.8V
Static Torque: 0.9kg.cm (12.65 oz.in)@4.8V
Speed: 0.08sec/60degrees@4.8V
Dead Band Width: ≤3us
Current Draw: Idle:0.12A; Running:0.33A; Stall:0.43A@5.0V
Servo Lead Gauge: 30#
Micro Coreless Motor
Dimensions 19x19.5x8mm
Weight: 4.5g
Here are some test videos for our product you can check:
GN D90 and D95 digital servo test video:
http://www.tudou.com/programs/view/K46jJUnIAmE/
GN D90MG digital servo test video:
http://www.tudou.com/programs/view/jpG1KIEe2Fo/
GN D95MG digital servo test video
http://www.tudou.com/programs/view/gmmKieIzCCk/
GN D39BB and D45BB digital servo test video:
http://www.tudou.com/programs/view/2afkP_gdXxY/
Gening RC Tech Co. Ltd. (china)
alice@geningrc.com
gn.harvest@gmail.com
http://www.geningrc.com
Below is a brief introduction of our digital servos. You can find more in the attached document and on our website: http://www.geningrc.com
GN Digital Servo Features:
It is high performance micro digital servo and is specially designed for 3D airplanes and helicopters, and glider application.
GN High-Speed Digital Servo provides extremely accurate neutral position. These servos are tailored for
3D fixed wing planes and micro electric helicopters. These digital servos can also find their position in the field of industrial automation which needs accurate and high speed control.
High fidelity MCU and excellent algorithm make it works smoothly and keep high frequency noise minimized.
GN Digital Servos adopt Frequency Conversion Technology enabling cool running temps under wild and long time 3D flight! This also provides for lower power consumption and this advanced technology guarantees the durability of GN Digital Servo.
GN D90 Micro Digital Servo（as tail servo）
Specs:
Operating Voltage: 4.8-6.0 Volts
Operating Speed (4.8V): 0.08sec/60°
Operating Speed (6.0V): 0.07sec/60°
Stall Torque (4.8V): 1.8kg.cm
Stall Torque (6.0V): 2.0kg.cm
Dead Band Width: ≤3usec
Current Drain (4.8V): 5.0mA/idle and 130mA no load operating
Current Drain (6.0V): 6.0mA/idle and 140mA no load operating
Dimensions: 0.92" x 0.45"x 0.86" (23.6 x 11.6 x 22mm)
Weight: 9.8g
Bearing Type: Top Ball Bearing
Gear Type: Carbon-nylon Gears
Motor Type: 3-Pole Neodynium Magnet
Connector Wire Length: 170mm
Operating Angle: 40 Deg. one side pulse traveling 400usec
Operating Temperature Range: -20 to +60 Degree C
Features:
• High speed and sensitivity
• Accurate,centers well
• Full AVCS Gyro DS mode compliant
• Strong,smooth
• Fall safe feature (Lost Signal Protection) --- The Digital Servo holds its position and torque during occasional signal lost.
• Light weight but perdurable structure will not interfere the 3D maneuverability of your plane.
GN D90MG Micro Digital Servo(as tail servo)
Specs:
Operating Voltage: 4.8-6.0 Volts
Operating Speed (4.8V): 0.08sec/60°
Operating Speed (6.0V): 0.07sec/60°
Stall Torque (4.8V): 1.8kg.cm
Stall Torque (6.0V): 2.0kg.cm
Dead Band Width: ≤3usec
Current Drain (4.8V): 5.3mA/idle and 140mA no load operating
Current Drain (6.0V): 6.6mA/idle and 150mA no load operating
Dimensions: 0.92" x 0.45"x 0.86" (23.6 x 11.6 x 22mm)
Weight: 13g
Bearing Type: Top Ball Bearing
Gear Type: Metal Gears
Motor Type: 3-Pole Neodynium Magnet
Connector Wire Length: 170mm
Operating Angle: 40 Deg. one side pulse traveling 400usec
Operating Temperature Range: -20 to +60 Degree C
Features:
• High speed and sensitivity
• Accurate,centers well
• Full AVCS Gyro DS mode compliant
• Strong,Smooth
• Metallic Copper Gears
• Fall safe feature (Lost Signal Protection) --- The Digital Servo holds its position and torque during occasional signal lost.
• Light weight but perdurable structure will not interfere the 3D maneuverability of your plane.
GN D95 and D95MG Micro Digital Servo
Specs:
Operating Voltage: 4.8-6.0 Volts
Operating Speed (4.8V): 0.09sec/60°
Operating Speed (6.0V): 0.08sec/60°
Stall Torque (4.8V): 2.0kg.cm
Stall Torque (6.0V): 2.2kg.cm
Dead Band Width: ≤3usec
Current Drain (4.8V): 5.3mA/idle and 140mA no load operating
Current Drain (6.0V): 6.6mA/idle and 150mA no load operating
Dimensions: 0.92" x 0.45"x 0.86" (23.6 x 11.6 x 22mm)
Weight: 13g
Bearing Type: Top Ball Bearing
Gear Type: Metal Gears
Motor Type: 3-Pole Neodynium Magnet
Connector Wire Length: 170mm
Operating Angle: 45 Deg. one side pulse traveling 400usec
Operating Temperature Range: -20 to +60 Degree C
Features:
• Quick,strong,smooth
• Accurate,centers well
• Metallic Copper Gears
• Full AVCS Gyro DS mode compliant and all receiver
• Top Ball Bearing
• Fall safe feature (Lost Signal Protection) --- The Digital Servo holds its position and torque during occasional signal lost.
• Light weight but perdurable structure will not interfere the 3D maneuverability of your plane.
D39BB Nano Digital Servo (Equipped with two ball bearings)
SPEC:
working voltage range: 4.0V-6.2V
Dynamic Torque: 0.5kg.cm @4.8V
Static Torque: 0.8kg.cm @4.8V
Speed: 0.08sec/60degrees@4.8V
Dead Band Width: ≤3us
Current Draw: Idle:0.10A; Running:0.30A; Stall:0.40A@5.0V
Servo Lead Gauge: 30#
Micro Coreless motor
Dimensions 19x17.5x8mm
Weight: 3.9g
D45BB Nano Digital Servo (Equipped with two ball bearings)
SPEC:
working voltage range: 4.0V-6.2V
Dynamic Torque: 0.6kg.cm (8.4 oz.in)@4.8V
Static Torque: 0.9kg.cm (12.65 oz.in)@4.8V
Speed: 0.08sec/60degrees@4.8V
Dead Band Width: ≤3us
Current Draw: Idle:0.12A; Running:0.33A; Stall:0.43A@5.0V
Servo Lead Gauge: 30#
Micro Coreless Motor
Dimensions 19x19.5x8mm
Weight: 4.5g
Here are some test videos for our product you can check:
GN D90 and D95 digital servo test video:
http://www.tudou.com/programs/view/K46jJUnIAmE/
GN D90MG digital servo test video:
http://www.tudou.com/programs/view/jpG1KIEe2Fo/
GN D95MG digital servo test video
http://www.tudou.com/programs/view/gmmKieIzCCk/
GN D39BB and D45BB digital servo test video:
http://www.tudou.com/programs/view/2afkP_gdXxY/
Gening RC Tech Co. Ltd. (china)
alice@geningrc.com
gn.harvest@gmail.com
http://www.geningrc.com