PDA

View Full Version : Electric Motor Design and Construction

Pages : 1 2 3 4 5 6 7 8 9 10 11 [12] 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
  1. Ever thought you couldn't wind 16G???????
  2. actro 24-5 to 24-4
  3. FEMM 4.01 magnetic motor modelling software (free)
  4. basic question
  5. more free magnetic simulation software
  6. Are brushless motors dc or ac?
  7. Brushless Motor
  8. Inrunner rewind ??? No
  9. GBx 2.5, 11T 22awg
  10. More Newbie ????
  11. C/F enters build arena... have ???
  12. ??? Pet ???
  13. 3 phase explained
  14. Newbie needs help
  15. VCR tape drive controllers?
  16. Please Help? Homebuilt engine.
  17. Weak magnets vs Stronger magnets
  18. motor winding for a small prop
  19. Quick winding question..
  20. winding pictures, compilation
  21. same question on 3d wind
  22. Outrunner needs servicing
  23. 60statorpole helicopter direct drive
  24. Yo
  25. Motor made from surplus cell phone charger
  26. 3 stator motor
  27. High performance 10,000 rpm, 4kW short term, how big?
  28. High performance 10,000 rpm, 4kW short term, how big?
  29. single magnet motor?
  30. Axi 2820/10 Magnets
  31. First motor clicks when turned. Help?
  32. What thickness does Flux ring have to be?
  33. Wind diagrams??
  34. diference between 9 10 11 tooth motors.
  35. Who is building the GB 40.4mm stator
  36. meaning of PWM
  37. Maximum shaft diameter on 22m stators
  38. Regarding stators?
  39. Rewind with less turns or swap can with one that has less poles for higher RPM?
  40. Prop power absorbtion
  41. Servo Tester vs. TX/RX for Motor Testing
  42. How deep are GB's?
  43. Swiss/German SuperMagnete site in English
  44. brush or brushless
  45. Redcon RA3615/2100KV
  46. electric motor capacitors
  47. CD rom Motor test
  48. I need someone to rewind BP21 motors
  49. Nice Asus cd-rom motor!!!
  50. stators: 110mm/48slot or 84mm/36, 58mm/24, 35mm/18, 16mm/9
  51. help with magnet placement
  52. Wire length
  53. 22.7mm, 9 teeth, 6 pole rewind for 1800-2200KV HELP!
  54. Disassembling motors - How do you do it?
  55. Re-gluing a stator!?
  56. Short magnets to make one long one?
  57. Dislodging magnets
  58. DLRK, Thank you MorrisM
  59. I wanna build a motor, just for kicks
  60. wish i had a camera....
  61. AaABbBCcC...?
  62. Magnet width
  63. E-Flight 480 shaft change
  64. Freeze Plug Can/rotor
  65. New Sponsor for Electric Motor Design and Construction Forum
  66. Changing Shaft on Hacker motor
  67. 6 poles stator: worth a try?
  68. 20mm (or smaller) stator and LRK/DLRK...possible?
  69. Test setup and sensors required for measuring motor + propeller performance
  70. Outrunner Brushless motor A22L 22A KV920
  71. closed
  72. 3520 for d.i.y. winding
  73. hacker E3-49
  74. E-flite 400 park (rebuild)
  75. how to build brushless motor with for co-axial propellers.