PDA

View Full Version : Castle Creations

Pages : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 [23] 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
  1. schottky diode
  2. Berg ant. solder point
  3. Phx-35 = Phx-45???
  4. how safe the Phoenix 25 is at 25 amps
  5. Is it a Phoenix 45 or 35?
  6. Can the P-25 be flashed with Mamba software?
  7. What's going to happen to Berg6?
  8. Pixie 20P overload
  9. Got burned again!
  10. Suggestion Time
  11. Mamba software in Phoenix 10 ???
  12. Is there a new Phoenix 10 out?
  13. Defective MicroStamp RX?? Where to send?
  14. Limiting current with EPA
  15. Can the phoenix10 handle 4 servos?
  16. Phoenix CC10 repair
  17. Not Programmable by USB interface
  18. What Is Up With My Ccp25?!?!?!
  19. Should I or should I not 1.11r
  20. pheonix 10 with a Himaxx 4100 on 3S
  21. Fun Question for the Castle Geeks
  22. PHlink 1.11 vs 1.07
  23. 1.11 firmware on PH60/80 question
  24. PHX 45 cuts off 6 seconds into full throttle
  25. Can Auto Detect on Phoneix 25 Miscount Cells ????
  26. New CC10 Photo comparison to Old CC10
  27. PHX-35, version 2?
  28. reoccuring problem CC25
  29. Berg4* DSPII
  30. PNX25 BEC with 4s + 2 HS55 servos?
  31. Twin controllers & BEC issues
  32. PH-60 100% throttle problem
  33. phx-25 surging...
  34. Phoenix 80 question
  35. CC10.... it works fine but.....
  36. Phx-Link gone bad?
  37. Problem with my phx-25. Right after warranty
  38. twin setup question
  39. Do I need new firmware in my PHX-25?
  40. Running P60 on power supply
  41. Berg Programming Help
  42. P10 3s lipo 4 servos?
  43. Does the new PHX-10 handle 4s w/ BEC?
  44. Firmware and Manually Programming
  45. Phx firmware and programming
  46. CC mod question re:BEC
  47. Which model Phoenix do I have?
  48. Overloaded PHX-25
  49. can't program pheonix 10 w/ usb-link!
  50. HV controllers shown at Toledo?????
  51. Phoenix 25 Getting Awful Hot
  52. CC45 seems to be starting the motor on its own
  53. Problem w/ PHX-25 at max throttle.
  54. Problem With Phoenix 10.
  55. Did CC have anything new at Toledo?
  56. Do the new Futaba 9c super work with bergs?
  57. What`s the best software for phx-10 and 25
  58. Where Can I buy Berg These Days?
  59. Castle Creations ESC's and number of servos.
  60. One would think when a company.....
  61. Programming Berg 5 channel 5/6 ??
  62. After PH10 repair PHX-Link won't work
  63. The world according to Shawn P.
  64. Faulty CC45 - self fix pos?
  65. Phoenix 10 problems... again...
  66. turn around repair time?
  67. dual motor,dual phx 10, single battery question
  68. Futaba 14MZ and Berg Rcvr's
  69. phoenix-45
  70. Phoenix 60 PWM Frequency Question
  71. Whichh esc will I need
  72. rpm limits of the PH10 and PH25, a definative answer please
  73. Best cutoff setting for 3 lipo.
  74. PX45 software
  75. Motor turns wrong direction, stalls, then turns correct direction!