PDA

View Full Version : Castle Creations

Pages : 1 2 3 4 5 6 7 8 9 10 11 [12] 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
  1. F5B/F with P80
  2. All my CC controllers 'stutter' a little bit.
  3. Governor in V1.01 software and higher doesn't work
  4. Castle Creations's customer support
  5. Simple Ph 10 question
  6. What's up with Castle Creations?
  7. Calling Mr. Palmer
  8. Controller for Mega 22/20/2
  9. PHX Link software 1.03B
  10. CC45 and Phx-Link 1.02
  11. Phoenix Link Software files
  12. Phoenix 25 with 4S lipo
  13. Phx35 will not link!
  14. CC Pheonix 25 problem
  15. Higher cell count PHX80?
  16. High Voltage BEC
  17. Mamba-25
  18. Griffin 40A ESC with 4 servos
  19. What Settings for Razor 2500 and PHX25 and 10?
  20. Problem with Pixie 20P and GWS 400C
  21. Phoenix 25 - Why would they do this INTENIONALLY?
  22. Pixie 7 and Phx Link
  23. Motor start problem (CDROM motor)
  24. Is this a problem?
  25. Phoenix 45, Kont 500, 8 & 10 Cell, Fut 9ch
  26. Phoenix 10 w/ Axi 2212/34 chatter
  27. Phx 10, LVC cutoff when using both 2c and 3c lipoly?
  28. Sending in ESC for update
  29. Connecting batt negative to motor plate?
  30. Is this a possible ESC Issue
  31. Fixed Throttle Timing on Phoenix-25
  32. ID on new phoenix 45?
  33. PHX-10 "misfire" above half throttle
  34. Phoenix-25 Probems - New to Brushless
  35. Help! Phoenix 25 troubles
  36. Please read this !!!
  37. new pixie7 - help me cc
  38. what is my phoenix 45 doing
  39. CC vendors in the EU?
  40. 35pegasus nfg.
  41. New to Electrics - Phoenix 45 question
  42. UK 'Dealers'
  43. Problems using new MP Jet Outrunner with Phoenix-25
  44. Phoenix 45 how to enter in programming mode ?
  45. Clear Heat shrink for my Pheonix 10
  46. Phoenix link and programing for pistol grip?
  47. How long to repair?
  48. PHX-Link + Mac =?
  49. CC25 programming issue with Phx-link
  50. Mamba Link ???????
  51. problem with pheonix 25
  52. Did I do that? (pics)
  53. PH25 + MPJ 25 = Beeping and Heat - Help?
  54. Long Leads?
  55. PHx, CC10 and 'Internal error'
  56. Replacement PHX10 went dead
  57. Patric.....Shawn..........What is going ON?
  58. Astro 010 Controller not upgradeable?
  59. Anyone have problems programming Phoenix with older Futaba radios?
  60. locked up a 45??
  61. Trouble getting into CC phoenix 10 programming mode.
  62. astro 010 and cc/astro 10 esc
  63. Pixie 20P with micro heli
  64. What the correct freq to set my CC45 with my Mega 16/15/2
  65. CC phx25 timing
  66. 2s 700mAhr Lipo Cutoff Selection
  67. Version 1.2 Firmware
  68. Big thanks to Castle Creations from MARCEE
  69. What's happening with the Phoenix 10 govenor mode software improvement?
  70. PHX80 with Aveox 2726/1
  71. Low Governor and High Governor?
  72. Can't get PH80 and Hacker B40LMR to start
  73. Phoenix Link Is A Great Tool !
  74. Glitching on 35Mhz (Again)
  75. Dragon 35